Pioneer DJM-750 Owner's Manual - Page 14

Advanced Operations 1 CH SELECT 2 1234 MIC A B MST PARAMETER 4 3 AUTO TAP BPM 5 6 % 7 ms 8 Number Name 1 Effect display section 2 Channel select display section 3 AUTO (TAP) 4 BPM value display (3 digits) 5 BPM 6 Parameter display section 7 % (ms) 8 Beat display section Descriptions SOUND COLOR FX BOOST COLOR FX BEAT EFFECT The name of the selected effect is displayed. - - 1 The name of the channel to which the effect is applied is displayed. 1 1 1 [AUTO] lights when the BPM measurement mode is set to the auto mode. [TAP] lights when in the manual input mode. - 1 1 When in the auto mode, this displays the automatically detected BPM value. When the BPM cannot be detected, the previously detected BPM value is displayed and flashes. - 1 1 When in the manual input mode, this displays the BPM value that was input manually. This is always lit. - 1 1 This displays the parameters specified for the individual effects. When the [BEAT c, d] button is pressed, the corresponding beat fraction is displayed for 1 second. - - 1 When a value outside the parameter range is specified with the [BEAT c, d] button, the value does not change and the display flashes. These light according to the units for the different effects. - - 1 This lights according to the selected beat number position. - - 1 SOUND COLOR FX These are effects that change in association with the [COLOR] control.  Using the SOUND COLOR FX function 1 Press one of the [COLOR FX] selection buttons. This selects the type of effect. The button that was pressed flashes. ! Even if one of the [COLOR FX] selection buttons is already selected, when a different button is selected and pressed, that button is selected. ! For the types of effects, see BOOST COLOR FX/SOUND COLOR FX effect types on page 16. 2 Turn the effect channel selector switch. This selects the channel to which the effect is applied. - [1] - [4]: The effect is applied to the sound of the respective channel. - [MIC]: The effect is applied to the sound of [MIC] channel. - [CF.A], [CF.B]: The effect is applied to the sound of the crossfader's [A] (left) or [B] (right) side. - [MASTER]: The effect is applied to the sound of the [MASTER] channel. ! When the effect channel selector switch is turned while the [COLOR] control is turned to any position other than the center and an effect is being applied to the sound, the effect is canceled. 3 Turn the [COLOR] control. When the control is turned, the effect is applied to the sound.  Canceling the SOUND COLOR FX effect Press the [COLOR FX] selection button that is flashing. The effect is canceled. 14 En BOOST COLOR FX These are effects that change in association with the [BOOST] button, the [COLOR] control and the tempo (BPM = Beats Per Minute) of the currently playing track.  Using the BOOST COLOR FX function 1 Press [AUTO/TAP] button. Select the BPM measurement mode. - [AUTO]: The BPM is measured automatically from the audio signal that is being input. The [AUTO] mode is set when this unit's power is turned on. - [TAP]: The BPM is input manually by tapping the [TAP] button with a finger. ! The [AUTO] BPM measurement range is BPM = 70 to 180. With some tracks it may not be possible to measure the BPM correctly. If the BPM cannot be measured, the BPM value on the display flashes. In such cases, use the [TAP] button to input the BPM manually. 2 Press the [BOOST] button. The [BOOST] button lights. 3 Press one of the [COLOR FX] selection buttons. This selects the type of effect. The button that was pressed flashes. ! Even if one of the [COLOR FX] selection buttons is already selected, when a different button is selected and pressed, that button is selected. ! For the types of effects, see BOOST COLOR FX/SOUND COLOR FX effect types on page 16. 4 Turn the effect channel selector switch. This selects the channel to which the effect is applied.