Pioneer DMH-WT8600NEX Installation Manual - Page 11

Installing the GPS, antenna

Page 11 highlights

English Truss head screw or flush surface screw Be sure to use the screws supplied with this product. Installing the GPS antenna CAUTION Do not cut the GPS antenna lead to shorten it or use an extension to make it longer. Altering the antenna cable could result in a short circuit or malfunction and permanent damage to this product. Installation notes • The antenna should be installed on a level surface where radio waves will be blocked as little as possible. Radio waves cannot be received by the antenna if reception from the satellite is blocked. • Take care not to pull the antenna lead when removing the GPS antenna. The lead may become detached. • Do not paint the GPS antenna, as this may affect its performance. When installing the antenna inside the vehicle (on the dashboard or rear shelf) WARNING Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as doing so may interfere with the proper functioning of such sensors or vents and may compromise the ability of the metal sheet under the GPS antenna to properly and securely affix to the dashboard. Make sure the surface is free of moisture, dust, grime, oil, etc., before affixing the metal sheet. Dashboard Rear shelf • When installing the GPS antenna inside the vehicle, be sure to use the metal sheet provided with your system. If this is not used, the reception sensitivity will be poor. • Do not cut the accessory metal sheet. This would reduce the sensitivity of the GPS antenna. GPS antenna Metal sheet Peel off the protective sheet on the rear. Double-sided tape Clamps Use clamps to secure the lead where necessary inside the vehicle. NOTES • Affix the metal sheet on the surface as level as possible where the GPS antenna faces the window. • Affix the GPS antenna on the metal sheet using the double-sided tape. • The metal sheet contains a strong adhesive which may leave a mark on the surface if it is removed. • When attaching the metal sheet, do not cut it into small pieces. • Some models use window glass that does not allow signals from GPS satellites to pass through. On such models, install the GPS antenna on the outside of the vehicle. En 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52

11
En
English
Truss head screw or flush surface
screw
Be sure to use the screws supplied
with this product.
CAUTION
Do not cut the GPS antenna lead to
shorten it or use an extension to make it
longer. Altering the antenna cable could
result in a short circuit or malfunction and
permanent damage to this product.
The antenna should be installed on a
level surface where radio waves will be
blocked as little as possible. Radio waves
cannot be received by the antenna if
reception from the satellite is blocked.
Dashboard
Rear shelf
When installing the GPS antenna inside
the vehicle, be sure to use the metal
sheet provided with your system. If this is
not used, the reception sensitivity will be
poor.
Do not cut the accessory metal sheet.
This would reduce the sensitivity of the
GPS antenna.
Take care not to pull the antenna lead
when removing the GPS antenna. The
lead may become detached.
Do not paint the GPS antenna, as this
may affect its performance.
Installing the GPS
antenna
Installation notes
WARNING
Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as
doing so may interfere with the proper functioning of such sensors or vents and may
compromise the ability of the metal sheet under the GPS antenna to properly and securely
affix to the dashboard.
GPS antenna
Metal sheet
Peel off the protective sheet on the rear.
Double-sided tape
Clamps
Use clamps to secure the lead where necessary inside the vehicle.
NOTES
Affix the metal sheet on the surface as level as possible where the GPS antenna faces the
window.
Affix the GPS antenna on the metal sheet using the double-sided tape.
The metal sheet contains a strong adhesive which may leave a mark on the surface if it is
removed.
When attaching the metal sheet, do not cut it into small pieces.
Some models use window glass that does not allow signals from GPS satellites to pass
through. On such models, install the GPS antenna on the outside of the vehicle.
When installing the antenna inside the vehicle (on the dashboard or
rear shelf)
Make sure the surface is free of
moisture, dust, grime, oil, etc.,
before affixing the metal sheet.