Pioneer DVJ-X1 Owner's Manual - Page 41

Advanced Operations RELOOP/ EXIT LOOP OUT/ OUT ADJUST LOOP IN/ REALTIME CUE EMERGENCY LOOP MODE NORMAL/DJ DIRECTION FWD/REV REV 1, FWD ¡ PLAY/PAUSE 6 Jog dial Loop playback 5 This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position. s To create a loop 1. Press the PLAY/PAUSE (3/8) button to begin playback. 2. During playback, press the LOOP IN/REALTIME CUE but- ton. ¶ This step is unnecessary if you wish to use a previously recorded cue point as the loop-in point. ¶ During the time required for writing the loop-in point, the LOOP IN/REALTIME CUE button will flash for about 2 seconds. 3. During playback, press the LOOP OUT/OUT ADJUST but- ton at the point you wish to use as the loop-out point. ¶ Repeat play (loop play) will begin without break between the se- lected loop-in and loop-out points. ¶ The frame search function can be used to set more accurate out points. ¶ If an alternate viewing angle or audio channel is selected before setting a loop-out point, it may not possible to designate a loopout point. ¶ Loop-out points cannot be set during reverse play. s To cancel loop play During loop playback, press the RELOOP/EXIT button. ¶ The loop will be canceled and playback will continue normally past the loop-out point. s To change a loop-out point 1. During loop playback, press the LOOP OUT/OUT ADJUST button. ¶ The display will show the loop-out point time, and the LOOP OUT/ OUT ADJUST button will flash rapidly, while the LOOP IN/ REALTIME CUE button indicator turns off. 2. Press the manual search buttons (REV1, FWD¡) or rotate the jog dial. ¶ The loop-out point will change in one-frame units. ¶ The loop-out point cannot be moved to a location before the loopin point. ¶ To cancel the adjust mode and return to loop play, press the LOOP OUT/OUT ADJUST button or wait 30 seconds. ¶ The loop-out point cannot be adjusted during reverse play. s To return to a loop (reloop) After cancellation of a loop, press the RELOOP/EXIT button during normal playback. ¶ Playback will return to the loop-in point of the previously set loop, and loop play will resume. s Automatic loop-out setting (emergency loop) During playback, press the EMERGENCY LOOP button. ¶ The normal loop playback indicators will appear (flashing LOOP OUT/OUT ADJUST button and LOOP IN/REALTIME CUE button), and the EMERGENCY LOOP indicator will flash. ¶ The point at which the button is pressed will become the loop-in point, and a loop-out point will be set automatically as described below; loop playback will then continue between the two points. · If the immediately preceding BPM value is known, a point four beats afterwards will become the loop-out point. · If the immediately preceding BPM value is not known, the loopout point will be set four seconds after the loop-in point. · If either of the above two conditions come after the track end, the track end will be made the loop-out point. ¶ When the EXIT/RELOOP button is pressed, the loop play will end and normal playback will resume. ¶ Emergency loop is not supported during reverse play. ¶ The loop-out point cannot be changed during the period of time from the pressing of the EMERGENCY LOOP button till the beginning of loop playback. Further, if the unit is switched to reverse play before beginning of loop playback, loop playback will be canceled. Reverse play 5 This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position. Set the DIRECTION FWD/REV select switch to the REV position (forward). The REV indicator lights and playback occurs in reverse. ¶ The jog dial's operation to accelerate/decelerate playback is reversed. ¶ During reverse playback, loop points cannot be set nor loop-out points modified. ¶ When track search or loop play are performed, the jog dial's audio/ video memory status display will flash for 1-2 seconds and scratch/ reverse operations may not respond. About fader start play 5 This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position. When the supplied accessory control cord is used to connect the CONTROL connector of this player to the CONTROL connector of a DJ mixer DJM-300, DJM-500, DJM-600, DJM-3000, DJM-909, or DJM-707, raising the DJ mixer's channel fader lever simultaneously releases the player from cue standby, automatically starting instant playback. Fader start can also be started by using the cross fader operation; when the fader lever is returned to its original position, the player also returns to its cue point (back cue) and enters cue standby. (For connection instructions consult page 16). 41