Pioneer FH-P5000MP Owner's Manual - Page 40

Using subwoofer output, Audio Adjustments

Get Pioneer FH-P5000MP PDF manuals and user guides View all Pioneer FH-P5000MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Section 09 Audio Adjustments 3 Push Multi Control down to turn loudness off. Loud :OFF appears in the display. Using subwoofer output This unit is equipped with a subwoofer output which can be turned on or off. 1 Press AUDIO to select SUB.W. Press AUDIO until SUB.W appears in the display. 2 Push Multi Control up to turn subwoofer output on. SUB.W:ON appears in the display. Subwoofer output is now on. # To turn subwoofer output off, push Multi Control down. 3 Push Multi Control left or right to select the phase of subwoofer output. Push Multi Control left to select reverse phase and Phase:REV appears in the display. Push Multi Control right to select normal phase and Phase:NOR appears in the display. Adjusting subwoofer (low pass filter) settings When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Press AUDIO to select 80. Press AUDIO until 80 (subwoofer cut-off frequency) appears in the display. # When the subwoofer output is on, you can select 80. # If the subwoofer setting has been previously adjusted, the frequency of that previously selected will be displayed instead of 80. 2 Push Multi Control left or right to select cut-off frequency. Each pushing Multi Control left or right selects cut-off frequencies in the following order: 506380100125160200 (Hz) Only frequencies lower than those in the selected range are outputted from the subwoofer. 3 Push Multi Control up or down to adjust the output level of the subwoofer. Each pushing Multi Control up or down increases or decreases the level of the subwoofer. +6  24 is displayed as the level is increased or decreased. Adjusting low pass filter attenuation slope When the subwoofer output is on, you can adjust the continuity of sound between speaker units. 1 Press AUDIO to select SLOPE. Press AUDIO until SLOPE (subwoofer slope) appears in the display. # When the subwoofer output is on, you can select SLOPE. 2 Push Multi Control left or right to select slope. Each pushing Multi Control left or right selects slopes in the following order: 61218 (dB/oct.) Note When slope of subwoofer and high pass filter are -12dB, and same cut-off frequency, the phase is reversed 180 degrees at the cut-off frequency. In this case, reversing the phase assures improved sound continuity. 40 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
3
Push Multi Control down to turn loud-
ness off.
Loud :OFF
appears in the display.
Using subwoofer output
This unit is equipped with a subwoofer output
which can be turned on or off.
1
Press AUDIO to select SUB.W.
Press
AUDIO
until
SUB.W
appears in the dis-
play.
2
Push Multi Control up to turn subwoo-
fer output on.
SUB.W:ON
appears in the display. Subwoofer
output is now on.
#
To turn subwoofer output off, push
Multi Control
down.
3
Push Multi Control left or right to select
the phase of subwoofer output.
Push
Multi Control
left to select reverse
phase and
Phase:REV
appears in the display.
Push
Multi Control
right to select normal
phase and
Phase:NOR
appears in the display.
Adjusting subwoofer (low pass
filter) settings
When the subwoofer output is on, you can ad-
just the cut-off frequency and the output level
of the subwoofer.
1
Press AUDIO to select 80.
Press
AUDIO
until
80
(subwoofer cut-off fre-
quency) appears in the display.
#
When the subwoofer output is on, you can se-
lect
80
.
#
If the subwoofer setting has been previously
adjusted, the frequency of that previously se-
lected will be displayed instead of
80
.
2
Push Multi Control left or right to select
cut-off frequency.
Each pushing
Multi Control
left or right se-
lects cut-off frequencies in the following order:
50
³
63
³
80
³
100
³
125
³
160
³
200
(Hz)
Only frequencies lower than those in the se-
lected range are outputted from the subwoo-
fer.
3
Push Multi Control up or down to ad-
just the output level of the subwoofer.
Each pushing
Multi Control
up or down in-
creases or decreases the level of the subwoo-
fer.
+6
±
±
24
is displayed as the level is
increased or decreased.
Adjusting low pass filter
attenuation slope
When the subwoofer output is on, you can ad-
just the continuity of sound between speaker
units.
1
Press AUDIO to select SLOPE.
Press
AUDIO
until
SLOPE
(subwoofer slope)
appears in the display.
#
When the subwoofer output is on, you can se-
lect
SLOPE
.
2
Push Multi Control left or right to select
slope.
Each pushing
Multi Control
left or right se-
lects slopes in the following order:
6
³
12
³
18
(dB/oct.)
Note
When slope of subwoofer and high pass filter are
-12dB
, and same cut-off frequency, the phase is
reversed 180 degrees at the cut-off frequency. In
this case, reversing the phase assures improved
sound continuity.
Audio Adjustments
En
40
Section
09