Pioneer GM-D8601 Owner's Manual - Page 11

Before installing the amplifier, Attaching the Bass boost, remote control, Example of installation

Get Pioneer GM-D8601 PDF manuals and user guides View all Pioneer GM-D8601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installation Section 04 English Before installing the amplifier WARNING ! To ensure proper installation, use the supplied parts in the manner specified. If any parts other than those supplied are used, they may damage internal parts of the amplifier, or become loose causing the amplifier to shut down. ! Do not install in: - Places where it could injure the driver or passengers if the vehicle stops suddenly. - Places where it may interfere with the dri- ver, such as on the floor in front of the driver's seat. ! Install tapping screws in such a way that the screw tip does not touch any wire. This is important to prevent wires from being cut by vibration of the car, which can result in fire. ! Make sure that wires do not get caught in the sliding mechanism of the seats or touch the legs of a person in the vehicle as short-circuit may result. ! When drilling to install the amplifier, always confirm no parts are behind the panel and protect all cables and important equipment (e.g. fuel/brake lines, wiring) from damage. CAUTION ! To ensure proper heat dissipation of the ampli- fier, ensure the following during installation: - Allow adequate space above the amplifier for proper ventilation. - Do not cover the amplifier with a floor mat or carpet. ! Place all cables away from hot places, such as near the heater outlet. ! The optimal installation location differs de- pending on the car model. Secure the amplifier at a sufficiently rigid location. ! Check all connections and systems before final installation. ! After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed. Attaching the Bass boost remote control Attach with tapping screws (3 mm × 10 mm (1/8 in. × 3/8 in.)) at an easily accessible location such as under the dashboard. Tapping screws (3 mm × 10 mm (1/8 in. × 3/8 in.)) Example of installation on the floor mat or chassis 1 Place the amplifier in the desired installation location. Insert the supplied tapping screws (4 mm × 18 mm (5/32 in. × 3/4 in.)) into the screw holes and push on the screws with a screwdriver so they make an imprint where the installation holes are to be located. 2 Drill 2.5 mm (3/32 in.) diameter holes at the imprints either on the carpet or directly on the chassis. En 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Before installing the amplifier
WARNING
!
To ensure proper installation, use the supplied
parts in the manner specified. If any parts
other than those supplied are used, they may
damage internal parts of the amplifier, or be-
come loose causing the amplifier to shut
down.
!
Do not install in:
—
Places where it could injure the driver or
passengers if the vehicle stops suddenly.
—
Places where it may interfere with the dri-
ver, such as on the floor in front of the dri-
ver
’
s seat.
!
Install tapping screws in such a way that the
screw tip does not touch any wire. This is im-
portant to prevent wires from being cut by vi-
bration of the car, which can result in fire.
!
Make sure that wires do not get caught in the
sliding mechanism of the seats or touch the
legs of a person in the vehicle as short-circuit
may result.
!
When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
CAUTION
!
To ensure proper heat dissipation of the ampli-
fier, ensure the following during installation:
—
Allow adequate space above the amplifier
for proper ventilation.
—
Do not cover the amplifier with a floor mat
or carpet.
!
Place all cables away from hot places, such
as near the heater outlet.
!
The optimal installation location differs de-
pending on the car model. Secure the ampli-
fier at a sufficiently rigid location.
!
Check all connections and systems before
final installation.
!
After installing the amplifier, confirm that the
spare tire, jack and tools can be easily re-
moved.
Attaching the Bass boost
remote control
Attach with tapping screws (3 mm × 10 mm
(1/8 in. × 3/8 in.)) at an easily accessible loca-
tion such as under the dashboard.
Tapping screws (3 mm × 10 mm
(1/8 in. × 3/8 in.))
Example of installation on
the floor mat or chassis
1
Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm ×
18 mm (5/32 in. × 3/4 in.)) into the screw holes
and push on the screws with a screwdriver so
they make an imprint where the installation
holes are to be located.
2
Drill 2.5 mm (3/32 in.) diameter holes at
the imprints either on the carpet or directly
on the chassis.
En
11
English
Section
04
Installation