Pioneer MJ-D707 Service Manual - Page 63

DETAILS OF ERROR DISPLAY, Removal of the Head Lifter, Head Lifter Installation

Page 63 highlights

MJ-D707, MJ-17D Removal of the Head Lifter 1 Remove the Lifter SP. 2 Tilt the Head Lifter to the rear and push part A to disengage it. Head Lifter Head Lifter Installation 1 Install part A in the Servo Base with the Head Lifter tilted to the back. 2 Match the Head Lifter and the Servo Base as shown in the figure, and then engage part B. 3 While holding part B with your hand, tilt the Head Lifter to the front and install the Lifter SP. 2 Push 1 Lifter SP Part A Head Lifter 2 Head Lifter 1 Part A 3 Push Part B Servo Base Part B Matching Position 7.2.2 DETAILS OF ERROR DISPLAY Error Display Details of Error Measure Can't REC ÷ DEFECT occurred 10 times continuously during REC-PLAY. ÷ Recordable cluster became 0 since DEFECT occurred during REC-PLAY. ÷ Address is unreadable. REC state can not be set for 20 seconds even after try again. ÷ Check if there are scratches, dusts, fingerprints, or black spots on disc. Check if disc fluctuates eccentrically or moves up and down largely. Can't COPY ÷ Determined as follows according to the channel status of the signals input from D-IN during REC-PAUSE or REC-PLAY. 1. Other than audio 2. Other than consumer use 3. Copy NG due to inversion of COPY bit of CD ÷ Check if CD is copy-proof. (Example: CD-R, etc.) D-IN UNLOCK ÷ The following occurred for digital signal input from D-IN during REC-PAUSE, REC-PLAY, or CD FUNC playback 1. Digital IN PLL unlocked. 2. Locked at other than FS = 32, 44.1 and 48 kHz. ÷ Check if D-IN signal line is normal. TOC FULL ÷ No area for registering music number and character information ÷ Replace with recording/playback disc with space for during REC-PLAY (music name, disc number, etc.) registering UTOC. UTOC R ERROR ÷ FTNO > LTNO. ÷ FTNO ≠ 0 or 1. ÷ UTOC recorded on DISC could not be read. ÷ Replace with other discs to check if UTOC data is normal. UTOC ERR A ÷ Start address > End address. ÷ Replace with other discs to check if UTOC data is normal. UTOC ERR L ÷ Any one data of UTOC 0 to 4 has looped. ÷ Replace with other discs to check if UTOC data is normal. 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68

MJ-D707, MJ-17D
63
1
2
Head Lifter
Lifter SP
Push
Part A
1
3
2
Head Lifter
Head Lifter
Servo Base
Part A
Push
Part B
Part B
Matching
Position
Error Display
Can't REC
Can't COPY
D-IN UNLOCK
TOC FULL
UTOC R ERROR
UTOC ERR A
UTOC ERR L
7.2.2 DETAILS OF ERROR DISPLAY
Details of Error
÷
DEFECT occurred 10 times continuously during REC-PLAY.
÷
Recordable cluster became 0 since DEFECT occurred during
REC-PLAY.
÷
Address is unreadable. REC state can not be set for 20 seconds
even after try again.
÷
Determined as follows according to the channel status of the
signals input from D-IN during REC-PAUSE or REC-PLAY.
1. Other than audio
2. Other than consumer use
3. Copy NG due to inversion of COPY bit of CD
÷
The following occurred for digital signal input from D-IN during
REC-PAUSE, REC-PLAY, or CD FUNC playback
1. Digital IN PLL unlocked.
2. Locked at other than FS = 32, 44.1 and 48 kHz.
÷
No area for registering music number and character information
during REC-PLAY (music name, disc number, etc.)
÷
FTNO > LTNO.
÷
FTNO
0 or 1.
÷
UTOC recorded on DISC could not be read.
÷
Start address > End address.
÷
Any one data of UTOC 0 to 4 has looped.
Measure
÷
Check if there are scratches, dusts, fingerprints, or black
spots on disc. Check if disc fluctuates eccentrically or
moves up and down largely.
÷
Check if CD is copy-proof. (Example: CD-R, etc.)
÷
Check if D-IN signal line is normal.
÷
Replace with recording/playback disc with space for
registering UTOC.
÷
Replace with other discs to check if UTOC data is normal.
÷
Replace with other discs to check if UTOC data is normal.
÷
Replace with other discs to check if UTOC data is normal.
Removal of the Head Lifter
Head Lifter Installation
1
Remove the Lifter SP.
2
Tilt the Head Lifter to the rear and push part A to disengage it.
1
Install part A in the Servo Base with the Head Lifter tilted to the
back.
2
Match the Head Lifter and the Servo Base as shown in the figure,
and then engage part B.
3
While holding part B with your hand, tilt the Head Lifter to the
front and install the Lifter SP.