Pioneer ND-BC2 Owner's Manual - Page 2

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Information to User Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment. If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. WARNING: Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after handling. IMPORTANT SAFEGUARDS • Installation and wiring of this product require specialist skill and experience. To assure your safety, please request a specialist technician to install the unit. • Do not attempt to heat the surface of the camera lens or camera lens itself with a lighter and so on when they have become frozen. This can cause a malfunction. • This product is a rear view camera for checking the view at the rear of a car. A rear view camera is a camera that provides symmetrical images in the same way as rear and side view mirrors. • Connection to a TV with an RCA video input is possible, but confirm whether the TV you use has a reverse gear connection function. • Direct sunlight or strong light (sunlight reflected from a bumper etc) on the camera may result in smear above and below the location where the light strikes, but this is not a malfunction. • This product is designed to supplement the driver' s rear view, but the camera images do not show all dangers and obstacles. Be sure to look behind you when reversing to confirm the view. • This product features a wide-angle lens, so the near view is wide and the far view is narrow, which may create a false sense of distance. Be sure to look behind you when reversing to confirm the view. • Do not wash your car with an automatic car wash or high-pressure water as it may result in water entering the camera or the camera falling off. • Check camera stand installation before driving. Are the screws loose? - Is the camera stand firmly secured? - If the rear view camera comes loose while you are driving it may cause an accident. Installation Parts supplied Rear view camera × 1 RCA power supply cable × 1 Power supply unit × 1 Hexagon wrench × 1 Velcro tape (soft type) × 1 Velcro tape (hard type) × 1 Clamp × 10 Waterproof pad × 1 Double-sided tape × 1 Camera stand bracket × 1 Installation example (Fig. 1) ① Glass surface ② Make sure it doesn't touch the wiper ③ Install on the center part Changing the orientation of camera stand installation (Fig. 11-1) The camera stand can be installed in various ways by changing the direction in which camera stand bracket is attached or attaching camera stand bracket . Change to match your car's shape or the installation site. 1. Use the hexagon wrench to remove the screws securing camera stand brackets and . (Fig. 2) 2. Change the direction of installation bracket . (Fig. 3-1) 3. Reattach with the screws. Installing Using Camera Stand Bracket (Fig. 11-4) 1. Use the hexagon wrench to remove the screws securing camera stand brackets and . (Fig. 2) 2. Attach camera stand bracket to the camera stand. (Fig. 3-2) 3. Attach the rear view camera to camera stand bracket . (Fig. 3-3) 4. Attach the camera stand and rear view camera. (Fig. 3-4) Route the cables as shown in the figure so that they do not become entangled. Attach the camera stand while being careful not to mistake the vertical orientation of the rear view camera. (Fig. 7) Installation Procedure Note: • Before making a final installation of the unit, temporarily connect the wiring to confirm that the connections are correct and the system works properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. • Install the unit where it does not get in the driver' s way and cannot injure the passenger if there is a sudden stop, like an emergency stop. • When mounting this unit, make sure none of the leads are trapped between this unit and the surrounding metalwork or fittings. • To prevent electric shock, do not install the power supply unit in places where it might come in contact with liquids. • Do not mount this unit near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it. (Never install in locations such as the above because of the danger of malfunction due to high temperatures.) • Before drilling any mounting holes always check behind where you want to drill the holes. Do not drill into the gas line, brake line, electrical wiring or other important parts. • If this unit is installed in the passenger compartment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident. • If this unit is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit. • Locate in the position you want to install the rear view camera. Adjust the angle of the rear view camera, and install so that the camera doesn't touch the car. • When sticking to a glass surface, stick it on in a position that assures the camera doesn't touch the rear window. • Install so that it does not obstruct the rear field of view. • Install so that it does not protrude from the side of the car. • Do not perform installation in rain or fog. • When humidity is high, dry the surface to which the unit is to be attached before installing. Moisture on the attachment surface reduces adhesive strength which may lead to the unit coming off. • If the temperature of the attachment surface is low, warm with a hair dryer of other means before installing to improve adhesive strength. • Do not attach the camera stand to areas on the car body treated with fluorocarbon resin, or glass. This may result in the rear view camera falling off. • During the 24-hour period after installing: - Do not apply water to the unit. - Do not expose the unit to rain. - Do not subject the camera to unnecessary force. • Thoroughly clean where tape is used for sticking on the unit. 1. Clean the surface to which the rear view camera is to be installed. (Fig. 4) Use a cloth or other item to wipe oil, wax, dust and any other dirt from the installation surface. 2. Remove the rear view camera from the camera stand. (Fig. 5) Remove the mounting screws with the hexagon wrench provided. ① Top ② Rear view camera ③ Bottom ④ Installation screw ⑤ Camera stand 3. Align the camera stand with the installation surface. (Fig. 6) Adjust the camera stand so that there is no space between it and the installation surface. ① Turn ② Twist ③ Camera stand 4. Attach the camera stand removed in step 2 to the rear view camera with the mounting screws. (Fig. 7) The rear view camera has a mark indicating the top of the camera. Attach the camera stand while being careful not to mistake the vertical orientation of the rear view camera. ① Top ② Bottom ③ Mark 5. Peel off the sheet on the back of they camera stand and stick it on. (Fig. 8, Fig. 9) Press the camera stand with your fingers to stick it to the installation surface. Touching the adhesive surface or sticking the unit on a second time reduces adhesive power which may result in the unit coming off. ① Camera stand ② When sticking to the center ③ When attaching using camera stand bracket (attaching while rotating by 90°) 6. Adjust the angle so that the bumper or rear edge of the car is displayed at the bottom of the TV screen. (Fig. 10, Fig. 11-2, Fig. 11-3, Fig. 12) ① Angle of view Horizontal: 135° ② Angle of view Vertical: 100° ③ Bumper or rear edge of car 7. Attach the power supply unit. (Fig. 13) Affix the Velcro tape (hard type) to the bottom of the power supply unit, and affix the Velcro tape (soft type) to the mounting location. ① Power supply unit ② Velcro tape (hard type) ③ Velcro tape (soft type) • You can use Velcro tape (hard type) to attach directly to a carpet, but do not use the soft type. • Install the power supply unit close enough for the rear view camera cable to reach. Si desea deshacerse de este producto, no lo mezcle con los residuos generales de su hogar. De conformidad con la legislación vigente, existe un sistema de recogida distinto para los productos electrónicos que requieren un procedimiento adecuado de tratamiento, recuperación y reciclado. Las viviendas privadas en los 25 estados miembros de la UE, en Suiza y Noruega pueden devolver gratuitamente sus productos electrónicos usados en las instalaciones de recolección previstas o bien en las instalaciones de minoristas (si adquieren un producto similar nuevo). En el caso de los países que no se han mencionado en el párrafo anterior, póngase en contacto con sus autoridades locales a fin de conocer el método de eliminación correcto. Al actuar siguiendo estas instrucciones, se asegurará de que el producto de desecho se somete a los procesos de tratamiento, recuperación y reciclaje necesarios, con lo que se previenen los efectos negativos potenciales para el entorno y la salud humana. PRECAUCIONES DE SEGURIDAD IMPORTANTES • La instalación y cableado de este producto requiere la habilidad y experiencia de un especia-lista. Para asegurar la seguridad, solicite un técnico especialista para instalar la unidad. • No intente calentar la superficie del objetivo de la cámara o el propio objetivo de la cámara con un encendedor o algo similar cuando los mismos estén congelados. Eso puede causar un fallo de funcionamiento. • Este producto es una cámara de vista posterior para verificar la vista en la parte trasera de un coche. Una cámara de vista posterior es una cámara que provee imágenes simétricas de la misma manera que los espejos retrovisores o laterales. • Se puede hacer la conexión a un televisor con entrada de vídeo RCA, pero compruebe si el televisor tiene una función de conexión de marcha atrás. • La luz directa del sol o luz fuerte (luz del sol reflejada de un parachoques, etc.) en la cámara puede producir una mancha por encima y por debajo de la ubicación donde la luz radia, pero esto no es un fallo de funcionamiento. • Este producto ha sido diseñado para complementar la vista trasera del conductor, pero las imágenes de la cámara no muestran todos los peligros y obstáculos. Asegúrese de mirar atrás cuando vaya de marcha atrás para comprobar la vista. • Este producto tiene una lente de gran angular y, por lo tanto, la vista cercana es amplia y la vista distante es estrecha, lo que puede crear una sensación falsa de la distancia. Asegúrese de mirar atrás cuando vaya de marcha atrás para comprobar la vista. • No lave su coche en un túnel de lavado automático o agua de alta presión, ya que esto puede resultar en la entrada de agua en la cámara o caída de la cámara. • Verifique la instalación del soporte de la cámara antes de conducir el coche. ¿No están flojos los tornillos? - ¿Está firmemente fijo el soporte de la cámara? - Si la cámara de vista posterior se afloja mientras está conduciendo, esto puede causar un accidente.