Pioneer VSX-530-K Owner's Manual - Page 35

Resetting the main unit, Cleaning the unit, Specifications - factory reset

Get Pioneer VSX-530-K PDF manuals and user guides View all Pioneer VSX-530-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

6 Additional information Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down BAND, press and hold STANDBY/ON for about two seconds. 3 When you see RESET? appear in the display, press AUTO SURROUND/STREAM DIRECT. OK? shows in the display. 4 Press ALC/STANDARD SURR to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. Important • If the ARC function is ON, you may not be able to initialize the unit. If this happens, turn OFF the ARC function or turn OFF all the connected device before turning OFF (STANDBY) the power for this unit, and initialize after the HDMI indicator goes out. • If the Standby Through is not set to OFF, you may not be able to initialize the unit. Cleaning the unit • Use a polishing cloth or dry cloth to wipe off dust and dirt. • When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers. • Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface. Specifications Amplifier section Continuous average power output of 80 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.08 %** total harmonic distortion. Front (stereo 80 W + 80 W Power output (1 kHz, 6 , 1 140 W per channel Guaranteed speaker impedance 6  to 16  * Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers ** Measured by Audio Spectrum Analyzer Audio Section Input (Sensitivity/Impedance) LINE 200 mV/47 k Signal-to-Noise Ratio (IHF, short circuited, A network) LINE 98 dB Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)] LINE 79 dB Video Section Signal level Composite 1 Vp-p (75 ) Tuner Section Frequency Range (FM 87.5 MHz to 108 MHz Antenna Input (FM 75  unbalanced Frequency Range (AM 530 kHz to 1700 kHz Antenna (AM Loop antenna Bluetooth section Version Bluetooth Specification Ver. 3.0 Output Bluetooth Specification Class 2 Estimated line-of-sight transmission distance About 10 m (33 ft.) Frequency range 2.4 GHz Supported Bluetooth profiles A2DP Supported Codec SBC (Subband Codec), AAC, APT-X * The line-of-sight transmission distance is an estimate. Actual transmission distances supported may differ depending on surrounding conditions. Digital In/Out Section HDMI terminal Type A (19-pin) HDMI output type 5 V, 55 mA USB terminal USB2.0 Full Speed (Type A) 5 V, 0.5 A Miscellaneous Power Requirements AC 120 V, 60 Hz Power Consumption 415 W In standby 0.1 W Dimensions . . . . . .435 mm (W) x 168 mm (H) x 331.5 mm (D) 171/8 in. (W) x 65/8 in. (H) x 131/16 in. (D) Weight (without package 8.3 kg (18 lb 5 oz) 5 7 33 Furnished Parts Remote control 1 Dry cell batteries (AAA size IEC R03 2 AM loop antenna 1 FM wire antenna 1 Warranty card 1 Quick start guide 1 Safety Brochure 1 SPEAKER CAUTION Sheet (English only 1 These operating instructions (CD-ROM) Note • Specifications and the design are subject to possible modifications without notice, due to improvements. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
5
Additional information
6
35
33
7
Resetting the main unit
Use this procedure to reset all the receiver’s settings to the
factory default. Use the front panel controls to do this.
1
Switch the receiver into standby.
2
While holding down
BAND
, press and hold
STANDBY/ON
for about two seconds.
3
When you see RESET? appear in the display, press
AUTO SURROUND/STREAM DIRECT
.
OK?
shows in the display.
4
Press
ALC/STANDARD SURR
to confirm.
OK
appears in the display to indicate that the receiver
has been reset to the factory default settings.
Important
•
If the ARC function is ON, you may not be able to initialize
the unit. If this happens, turn OFF the ARC function or turn
OFF all the connected device before turning OFF
(STANDBY) the power for this unit, and initialize after the
HDMI indicator goes out.
•
If the
Standby Through
is not set to
OFF
, you may not be
able to initialize the unit.
Cleaning the unit
•
Use a polishing cloth or dry cloth to wipe off dust and dirt.
•
When the surface is dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six times with water,
and wrung out well, and then wipe again with a dry cloth.
Do not use furniture wax or cleansers.
•
Never use thinners, benzine, insecticide sprays or other
chemicals on or near this unit, since these will corrode the
surface.
Specifications
Amplifier section
Continuous average power output of 80 watts* per
channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no
more than 0.08 %** total harmonic distortion.
Front (stereo) . . . . . . . . . . . . . . . . . . . . . . . . . . .80 W + 80 W
Power output (1 kHz, 6
, 1 %). . . . . . . . . . 140 W per channel
Guaranteed speaker impedance . . . . . . . . . . . . . . 6
to 16
* Measured pursuant to the Federal Trade Commission’s Trade
Regulation rule on Power Output Claims for Amplifiers
** Measured by Audio Spectrum Analyzer
Audio Section
Input (Sensitivity/Impedance)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/47 k
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 dB
Video Section
Signal level
Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75
)
Tuner Section
Frequency Range (FM) . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
Antenna Input (FM) . . . . . . . . . . . . . . . . . . . . 75
unbalanced
Frequency Range (AM) . . . . . . . . . . . . . . . 530 kHz to 1700 kHz
Antenna (AM). . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna
Bluetooth
section
Version . . . . . . . . . . . . . . . . . .
Bluetooth
Specification Ver. 3.0
Output
. . . . . . . . . . . . . . . . . .
Bluetooth
Specification Class 2
Estimated line-of-sight transmission distance*
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . About 10 m (33 ft.)
Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 GHz
Supported
Bluetooth
profiles . . . . . . . . . . . . . . . . . . . . . . A2DP
Supported Codec. . . . . . .SBC (Subband Codec), AAC, APT-X
* The line-of-sight transmission distance is an estimate.
Actual transmission distances supported may differ
depending on surrounding conditions.
Digital In/Out Section
HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . . Type A (19-pin)
HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 55 mA
USB terminal. . . . . . . . .USB2.0 Full Speed (Type A) 5 V, 0.5 A
Miscellaneous
Power Requirements . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz
Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 W
In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 W
Dimensions . . . . . .435 mm (W) x 168 mm (H) x 331.5 mm (D)
17
1
/
8
in. (W) x 6
5
/
8
in. (H) x 13
1
/
16
in. (D)
Weight (without package) . . . . . . . . . . . . . . .8.3 kg (18 lb 5 oz)
Furnished Parts
Remote control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Dry cell batteries (AAA size IEC R03) . . . . . . . . . . . . . . . . . . . 2
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM wire antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick start guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Brochure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPEAKER CAUTION Sheet (English only) . . . . . . . . . . . . . . . 1
These operating instructions (CD-ROM)
Note
•
Specifications and the design are subject to possible
modifications without notice, due to improvements.