Pioneer VSX-D814-S Operating Instructions - Page 72

Additional information, Resetting the main unit, Switching the speaker, impedance

Get Pioneer VSX-D814-S PDF manuals and user guides View all Pioneer VSX-D814-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

10 Additional information Problem Remedy No sound is output or a noise • Set the digital volume level of the player to full, or to the neutral is output when software with position. DTS is played back. When a search is performed • This is not a malfunction, but be sure to turn the volume down to by a DTS compatible CD prevent the output of loud noise from your speakers. player during playback, noise is output. Can't operate the remote control. • Replace the batteries (refer to page 5). • Operate within 7 m, 30° of the remote sensor on the front panel (refer to page 6). • Remove the obstacle or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. The display is dark or off. • Press FL DIMMER on the remote control repeatedly to return to the default. • If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions. Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver on. 2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press the TONE button. OK? shows in the display. 4 Press TONE once more to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. Switching the speaker impedance We recommend using speakers of 8Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6Ω impedance rating. • With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS / SPEAKER IMPEDANCE button. Each time you do this, you switch between the impedance settings: • SP 6 OHM - Use this setting if your speakers are rated at 6Ω. • SP 8 OHM - Use this setting if your speakers are rated at 8Ω or more. 72 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Additional information
10
72
En
•
If the unit does not operate normally due to external effects such as static electricity
disconnect the power plug from the outlet and insert again to return to normal operating
conditions.
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver on.
2
While holding down the TONE button,
press and hold the
±
STANDBY/ON
button for about three seconds.
3
When you see RESET? appear in the
display, press the TONE button.
OK?
shows in the display.
4
Press TONE once more to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory default
settings.
Switching the speaker
impedance
We recommend using speakers of 8
Ω
with
this system, but it is possible to switch the
impedance setting if you plan to use speakers
with a 6
Ω
impedance rating.
•
With the receiver in standby, press
±
STANDBY/ON while holding down the
SPEAKERS / SPEAKER IMPEDANCE button.
Each time you do this, you switch between the
impedance settings:
•
SP 6 OHM
– Use this setting if your
speakers are rated at 6
Ω
.
•
SP 8 OHM
– Use this setting if your
speakers are rated at 8
Ω
or more.
No sound is output or a noise
is output when software with
DTS is played back.
• Set the digital volume level of the player to full, or to the neutral
position.
When a search is performed
by a DTS compatible CD
player during playback, noise
is output.
• This is not a malfunction, but be sure to turn the volume down to
prevent the output of loud noise from your speakers.
Can’t operate the remote
control.
• Replace the batteries (refer to page 5).
• Operate within 7 m, 30° of the remote sensor on the front panel
(refer to page 6).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
The display is dark or off.
• Press
FL DIMMER
on the remote control repeatedly to return to
the default.
Problem
Remedy