Pioneer VSX-D912K Owner's Manual - Page 61

Clearing all the remote, control settings, Direct function, Confirming preset codes

Get Pioneer VSX-D912K PDF manuals and user guides View all Pioneer VSX-D912K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Controlling the rest of your system 10 Clearing all the remote control settings You can clear all presets and restore the factory default settings. 1 Press REMOTE SETUP and hold for three seconds. The LCD display shows SETUP. 2 Press any MULTI CONTROL button. 3 Use and to select RESET then press REMOTE SETUP. The LCD shows OK when you're done. Direct function • Default setting: ON You can use the direct function feature to control one component using the remote control while at the same time, using your receiver to playback a different component. This could let you, for example, use the remote control to set up and listen to a CD on the receiver and then use the remote control to rewind a tape in your VCR while you continue to listen to your CD player. When direct function is on, any component you select (using the MULTI CONTROL buttons ) will be selected by both the receiver and the remote control. When you turn direct function off, you can operate the remote control without affecting the receiver. 1 Press REMOTE SETUP and hold for three seconds. The LCD display shows SETUP. 2 Press the MULTI CONTROL button for the component you want to control. 3 Use and to select DIR SET then press REMOTE SETUP. The LCD on the remote displays the component you want to control. 4 Use the number buttons to enter either 9990 (direct on) or 9995 (direct off). The LCD will display OK to show the four digit code has been accepted. • You can't use direct function with the TVC function. Confirming preset codes Use this feature to check which preset code is assigned to a MULTI CONTROL button. 1 Press REMOTE SETUP and hold for three seconds. The LCD display shows SETUP. 2 Press the MULTI CONTROL button of the component for which you want to check the preset code. 3 Use and to select READ ID then press REMOTE SETUP. The preset code appears in the display for two seconds. 61 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Controlling the rest of your system
10
61
En
Clearing all the remote
control settings
You can clear all presets and restore the
factory default settings.
1
Press REMOTE SETUP and hold for
three seconds.
The
LCD display shows
SETUP
.
2
Press any MULTI CONTROL button.
3
Use
´
and
µ
to select RESET then
press REMOTE SETUP.
The LCD shows
OK
when you’re done.
Direct function
•
Default setting:
ON
You can use the direct function feature to
control one component using the remote
control while at the same time, using your
receiver to playback a different component.
This could let you, for example, use the
remote control to set up and listen to a CD on
the receiver and then use the remote control
to rewind a tape in your VCR while you
continue to listen to your CD player.
When direct function is on, any component
you select (using the
MULTI CONTROL
buttons ) will be selected by both the receiver
and the remote control. When you turn direct
function off, you can operate the remote
control without affecting the receiver.
1
Press REMOTE SETUP and hold for
three seconds.
The LCD display shows
SETUP
.
2
Press the MULTI CONTROL button for
the component you want to control.
3
Use
´
and
µ
to select DIR SET then
press REMOTE SETUP.
The LCD on the remote displays the compo-
nent you want to control.
4
Use the number buttons to enter
either 9990 (direct on) or 9995 (direct off).
The LCD will display
OK
to show the four digit
code has been accepted.
•
You can’t use direct function with the
TVC
function.
Confirming preset codes
Use this feature to check which preset code is
assigned to a
MULTI CONTROL
button.
1
Press REMOTE SETUP and hold for
three seconds.
The LCD display shows
SETUP
.
2
Press the MULTI CONTROL button of
the component for which you want to
check the preset code.
3
Use
´
and
µ
to select READ ID then
press REMOTE SETUP.
The preset code appears in the display for two
seconds.