Polk Audio Omni SB1 Soundbar User Guide - Page 5
Remote Control, IR Remote Learning, Connecting Your SB1 - polk system
View all Polk Audio Omni SB1 Soundbar manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
Remote Control Power- Turns on the bar or puts it in standby mode. Mute- Mutes and unmutes the sound coming from the sound bar. Source 1, 2, WiFI - Changes which input source you are listening to. Master Volume Up and Down ( + / - ) Adjusts the master volume of the system. Center Volume Up and Down ( + / - ) Adjusts the volume of the center channel. SUB Volume Up and Down ( + / - ) Adjusts the volume of the subwoofer. Movie/Music Select-Tailors the audio for either movies or music. IR Remote Learning Set Up Your TV's IR Remote Control For SmartBar™ Learning Note: For your sound bar to respond to your remote control, you MUST FIRST program the bar to respond to your television's original IR (Infra-Red) remote. An RF (Radio Frequency) remote will not work. Other remotes (cable, satellite) will work only after you have programmed the bar to respond to the TV's IR remote. Programming Instructions: Your sound bar is currently programmed to respond to the remote control that is included with the product. However, we strongly recommend programming the sound bar to also respond to your existing remote control using the steps illustrated below. This will enable you to operate all of your components using a single remote control. While programming the sound bar, ignore anything that may be displayed on the TV screen. Example: To teach your bar the "Volume Up" command of your remote control. 1. The Sound Bar is turned on and the LED is dim red, and you have sound coming from the bar. 2. P ress and hold the "SOURCE/LEARN" button (on either the bar or the included remote) for 5 seconds. LEDs 3, 5, 7, 9, 11 pulse. 3. Press and release "Volume Up" button on the SB1's included remote. 4. Hold your TV's remote 6" - 1' from the sound bar. 5. Press the "Volume Up" button on your TV's IR remote control once. 6. LEARN LEDs 3, 5, 7, 9, 11 turn solid; the command has been learned. Two chimes confirm the command has been learned. Repeat steps 1-6 to program "Volume Down"( - ), Source, Mute and Power buttons. Important note to save your tv's ir remote commands: After you've programmed all of the commands on your TV's remote control, press and hold the "Source/Learn" button for 5 seconds. This saves all of the commands. Note: If your bar fails to learn certain IR remote codes, the power LED will blink red three times. Try erasing any previously programmed codes (see below) and carefully repeat steps 1-6 above. Code Erasing Procedure: If you have programmed your Sound bar to respond to a remote control and you no longer want it to do so, erase the codes by pressing the "Source/Learn" button for 10 seconds. Previously learned codes have been successfully erased when the POWER LED flashes green ten times. Note: This procedure removes ALL of your bar's remote control programming. If you only need to change the programming for some of the bar buttons, follow the six steps in the sequence previously described to redo any previous programming. The Sound bar will continue to respond to the provided credit card remote control. Connecting Your SB1 Wi-Fi Setup 1. T o ensure the easiest setup, place your SB1 near your internet-connected wireless router. Note, when setup is complete, you can move your device anywhere you want to. 2. C onnect the included power cable to the SB1 and a power outlet. The device will power on automatically. 3. T he white light on the back will blink quickly for about 20 seconds, after which it will begin to pulse slowly. 4. T he slowly pulsing light means your device is ready to connect to your Wi-Fi network. Note: if the Wi-Fi LED is not pulsing slowly, Press and hold the Wi-Fi setup button (for 8 seconds), until you hear the second tone. 5. D ownload the Polk Omni App from the Apple App Store or Google Play Store. 6. Launch the app and follow the instructions. Utility App Note: to enable Wi-Fi Protected Setup (WPS) mode with a WPS compatible router, press and hold the Wi-Fi button on the SB1 for 4 seconds or until the first beep. Now push the WPS button on your wireless router. The SB1 will automatically connect to your network without the need to enter your password. 1. www.polkaudio.com 5