Poulan C38D User Manual - Page 9

CONTAINER MOUNTING, See Fig. 7, No hardware required, LOWER CHUTE See Fig. 8, Use Hardware -GROUP E

Page 9 highlights

6 CONTAINER ASSEMBLY (See Fig. 6) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ONBOTHHALVESMUSTOVERLAPTO FORMSEALASSHOWN IN INSET. 4. Repeat for second container. CONTAINER BOTTOM HALF 7 CONTAINER MOUNTING (See Fig. 7) No hardware required 1. Install one container to left side first with warning to outside of unit. Install other container to right side. NOTE: Right container should always overlap left container at center support. 2. Close cover and lock latch handle over center support tube. COVER LATCH HANDLE CONTAINER WARNING WARNING 02739 CONTAINER TOP HALF 02089 CONTAINER TOP HALF PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF CONTAINER BOTTOM HALF LOCKING TAB FIG. 6 ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. CONTAINER HANDLE csDWruaobcAjnkeoecRtdt otNooprewIdrNeaaatmeGramagnoedwdd.eUer tsuieenrlioeonsraslytcioaonnr.etCaciohnmeecrmkisebnpadrgoepfdreerrqelyupielsanctelym. Reenpt lcaocnetawinheern. 02082 FIG. 7 CENTER SUPPORT TUBE CONTAINER WARNING 8 LOWER CHUTE (See Fig. 8) Use Hardware - - GROUP "E" 1. Raise and hold deflector shield in upright position. 2. Slide back edge of chute over rear corner of mower deck and pivot forward. 3. Align slot in lower chute with hex bolt in mower deck baffle and close chute over deck openning. 4. Secure with washer and wing nut. CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. WASHER DEFLECTOR SHIELD MOWER DECK BAFFLE 02097 W DrenlndyoitesAlnyds.ouRrRteboepjNepplacelIatcrNcaetoetmGewwemenhaoterwcnoacennrratduacnkidneleeedtsrie.sorricodoraanmttiaoainng.eeCrdih.seUpcsrkoebpoaenglyfraeqreucomme 02343 WING NUT HEX BOLT 9 FIG. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21

9
02082
02343
CONTAINER MOUNTING
(See Fig. 7)
No hardware required
1.
Install one container to left side first with warning to
outside of unit. Install other container to right side.
NOTE
: Right container should always overlap left container
at center support.
2.
Close cover and lock latch handle over center support
tube.
7
COVER LATCH
HANDLE
CENTER
SUPPORT
TUBE
CONTAINER
WARNING
CONTAINER
HANDLE
FIG. 7
CONTAINER
WARNING
DEFLECTOR SHIELD
MOWER DECK
BAFFLE
WASHER
LOWER CHUTE (See Fig. 8)
Use Hardware - - GROUP "E"
1.
Raise and hold deflector shield in upright position.
2.
Slide back edge of chute over rear corner of mower
deck and pivot forward.
3.
Align slot in lower chute with hex bolt in mower deck
baffle and close chute over deck openning.
4.
Secure with washer and wing nut.
CAUTION: Do not remove discharge
guard from mower. Raise and hold
guard when attaching lower chute
and allow it to rest on chute while in
operation.
WING NUT
HEX BOLT
FIG. 8
8
PRESS TOGETHER
TO FORM SEAL
WHILE LIFTING
TOP HALF
02089
CONTAINER
BOTTOM
HALF
CONTAINER
TOP HALF
ASSEMBLY CHECK: Squeeze sides of lower half of con-
tainer and check that there is no gap between upper and
lower halves.
If a gap appears, unlock tabs to separate
container halves and repeat instructions above.
LOCKING
TAB
02097
FIG. 6
02739
CONTAINER
BOTTOM HALF
CONTAINER
TOP HALF
CONTAINER ASSEMBLY (See Fig. 6)
No hardware required
1.
Place bottom half inside of top half, as shown.
2.
Place one foot inside bottom half and lift top half to
meet bottom half.
3.
Press halves tightly together while lifting top to lock
into place as shown.
IMPORTANT
: BEFORE LOCKING THE TABS, HOOKED EDGES
ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN
IN INSET.
4.
Repeat for second container.
6