Poulan PO1538D User Manual - Page 23

To Remove Hood And Grill Assembly

Get Poulan PO1538D PDF manuals and user guides View all Poulan PO1538D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

SERVICE AND ADJUSTMENTS TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 27) • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. • To replace, reverse above procedure. HOOD HEADLIGHT WIRE CONNECTOR ENGINE TO ADJUST THROTTLE CONTROL CABLE (See Fig. 28) The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows: • With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position. • Check that holes "A" in governor control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely. GOVERNOR CONTROL LEVER GOVERNOR CONTROL PLATE HOLES "A" CLAMP SCREW FIG. 28 THROTTLE CABLE FIG. 27 TO ADJUST CARBURETOR The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual. High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
23
SERVICE AND ADJUSTMENTS
FIG. 28
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 27)
•
Raise hood.
•
Unsnap headlight wire connector.
•
Stand in front of tractor.
Grasp hood at sides, tilt toward
engine and lift off of tractor.
•
To replace, reverse above procedure.
FIG. 27
HEADLIGHT
WIRE
CONNECTOR
HOOD
GOVERNOR
CONTROL LEVER
GOVERNOR
CONTROL PLATE
THROTTLE
CABLE
HOLES “A”
TO ADJUST CARBURETOR
The carburetor has been preset at the factory and adjustment
should not be necessary.
However, minor adjustment may be
required to compensate for differences in fuel, temperature,
altitude or load.
If the carburetor does need adjustment,
see engine manual.
High speed stop is factory adjusted.
Do not adjust - dam-
age may result.
IMPORTANT:
NEVERTAMPERWITHTHE ENGINE GOVERNOR,
WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.
OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH
SPEED SETTING CAN BE DANGEROUS.
IF YOU THINK THE
ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,
CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/
DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND
EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.
CLAMP
SCREW
ENGINE
TO ADJUST THROTTLE CONTROL CABLE
(See Fig. 28)
The throttle control has been preset at the factory and
adjustment should not be necessary.
Check adjustment
as described below before loosening cable.
If adjustment
is necessary, proceed as follows:
•
With engine not running, move throttle control lever
from slow to choke position.
Slowly move lever from
choke to fast position.
•
Check that holes “A”
in governor control lever and hole
in governor plate line-up.
If holes “A” are not aligned,
loosen clamp screw and move throttle cable until
holes
are aligned.
Tighten clamp screw securely.
TO REPLACE HEADLIGHT BULB
•
Raise hood.
•
Pull bulb holder out of the hole in the backside of the
grill.
•
Replace bulb in holder and push bulb holder securely
back into the hole in the backside of the grill.
•
Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
•
Check wiring.
See electrical wiring diagram in the
Repair Parts section.
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse.
The
fuse holder is located behind the dash.