Poulan PP175G42 Owner Manual - Page 6

Assembly - parts list

Get Poulan PP175G42 PDF manuals and user guides View all Poulan PP175G42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 5/16" wrench Utility knife (2) 7/16" wrenches Tire pressure gauge (2) 1/2" wrenches Pliers (1) 9/16" wrench When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). TO REMOVE TRACTOR FROM CARTON UNPACK CARTON • Remove all accessible loose parts and parts cartons from carton. • Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat. • Check for any additional loose parts or cartons and remove. BEFORE REMOVING TRACTOR FROM SKID CONNECT BATTERY (See Fig. 1) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in the Maintenance section of this manual for charging instructions.) • Determine battery location. Battery location will be under the seat or the hood. • Lift seat pan or hood to raised position. • Remove two terminal caps and discard. • First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal. • Connect BLACK grounding cable to negative (-) terminal with remaining bolt and nut. Tighten securely. TERMINAL COVER NUT LABEL TERMINAL CAP BOLT POSITIVE (RED) CABLE 02605 NEGATIVE (BLACK) CABLE Fig. 1 • Lower seat pan or hood. NOTE: For battery installation see "REPLACING BATTERY" in the Service and Adjustments section in this manual. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
6
ASSEMBLY
TO REMOVE TRACTOR FROM CARTON
UNPACK CARTON
•
Remove all accessible loose parts and parts cartons
from carton.
•
Cut along dotted lines on all four panels of carton.
Remove end panels and lay side panels flat.
•
Check for any additional loose parts or cartons and
remove.
BEFORE REMOVING TRACTOR FROM
SKID
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely.
Use
the correct tools as necessary to ensure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier.
Standard
wrench sizes are listed.
(1) 5/16" wrench
Utility knife
(2) 7/16" wrenches
Tire pressure gauge
(2)
1/2" wrenches
Pliers
(1) 9/16" wrench
When right or left hand is mentioned in this manual, it means
when you are in the operating position (seated behind the
steering wheel).
CONNECT BATTERY (See Fig. 1)
WARNING:
Do not short battery terminals
by allowing a wrench or any other object
to contact both terminals at the same
time. Before connecting battery, remove
metal bracelets, wristwatch bands, rings,
etc. Positive terminal must be connected
first to prevent sparking from accidental
grounding.
NOTE:
If this battery is put into service after month and
year indicated on label (label is located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See
“BATTERY” in the Maintenance
section of this manual for
charging instructions.)
•
Determine battery location. Battery location will be
under the seat or the hood.
•
Lift seat pan or hood to raised position.
•
Remove two terminal caps and discard.
•
First connect RED battery cable to positive (+) terminal
with bolt and nut as shown. Tighten securely. Slide
terminal cover over terminal.
•
Connect BLACK grounding cable to negative (-)
terminal with remaining bolt and nut. Tighten securely.
Fig. 1
02605
NUT
POSITIVE
(RED)
CABLE
NEGATIVE
(BLACK)
CABLE
BOLT
TERMINAL
COVER
LABEL
TERMINAL
CAP
•
Lower seat pan or hood.
NOTE:
For battery
installation see “REPLACING BATTERY”
in the Service and Adjustments section in this manual.