Poulan PRRT65 User Manual - Page 19

Troubleshooting Points

Get Poulan PRRT65 PDF manuals and user guides View all Poulan PRRT65 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

TROUBLESHOOTING POINTS PROBLEM Will not start CAUSE 1. Out of fuel. 2. Engine not "CHOKED" properly. 3. Engine flooded. 4. Dirty air cleaner. 5. Water in fuel. 6. Clogged fuel tank. 7. Loose spark plug wire. 8. Bad spark plug or improper gap. 9. Carburetor out of adjustment. 10. Oil soaked air filter. Hard to start 1. Throttle control not set properly. 2. Dirty air cleaner. 3. Bad spark plug or improper gap. 4. Stale or dirty fuel. 5. Loose spark plug wire. 6. Carburetor out of adjustment. Loss of power 1. Engine is overloaded. 2. Dirty air cleaner. 3. Low oil level/dirty oil. 4. Faulty spark plug. 5. Oil in fuel. 6. Stale or dirty fuel. 7. Water in fuel. 8. Clogged fuel tank. 9. Spark plug wire loose. 10. Dirty engine air screen. 11. Dirty/clogged muffler. 12. Carburetor out of adjustment. 13. Poor compression. Engine overheats 1. Low oil level/dirty oil. 2. Dirty engine air screen. 3. Dirty engine. 4. Partially plugged muffler. 5. Improper carburetor adjustment. Excessive bounce/ difficult handling 1. Ground too dry and hard. Soil balls up or clumps 1. Ground too wet. Engine runs but tiller won't move 1. Drive control bar is not engaged. 2. V-belt not correctly adjusted. 3. V-belt is off pulley(s). Engine runs but labors when tilling 1. Tilling too deep. 2. Throttle control not properly adjusted. 3. Carburetor out of adjustment. Tines will not rotate 1. Shear pin(s) broken. CORRECTION 1. Fill fuel tank. 2. See "TO START ENGINE" in Operation section. 3. Wait several minutes before attempting to start. 4. Clean or replace air cleaner cartridge. 5. Empty fuel tank and carburetor, and refill tank with fresh gasoline. 6. Remove fuel tank and clean. 7. Make sure spark plug wire is seated properly on plug. 8. Replace spark plug or adjust gap. 9. Make necessary adjustments. 10. Replace air filter. 1. Place throttle control in "FAST" position. 2. Clean or replace air cleaner cartridge. 3. Replace spark plug or adjust gap. 4. Empty fuel tank and refill with fresh gasoline. 5. Make sure spark plug wire is seated properly on plug. 6. Make necessary adjustments. 1. Set depth stake for shallower tilling. 2. Clean or replace air cleaner cartridge. 3. Check oil level/change oil. 4. Clean and regap or change spark plug. 5. Empty and clean fuel tank and refill, and clean carburetor. 6. Empty fuel tank and refill with fresh gasoline. 7. Empty fuel tank and carburetor, and refill tank with fresh gasoline. 8. Remove fuel tank and clean. 9. Connect and tighten spark plug wire. 10. Clean engine air screen. 11. Clean/replace muffler. 12. Make necessary adjustments. 13. Contact an authorized service center/department. 1. Check oil level/change oil. 2. Clean engine air screen. 3. Clean cylinder fins, air screen, and muffler area. 4. Remove and clean muffler. 5. Adjust carburetor to richer position. 1. Moisten ground or wait for more favorable soil conditions. 1. Wait for more favorable soil conditions. 1. Engage drive control. 2. Inspect/adjust V-belt. 3. Inspect V-belt. 1. Set depth stake for shallower tilling. 2. Check throttle control setting. 3. Make necessary adjustments. 1. Replace shear pin(s). 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
19
Will not start
1. Out of fuel.
1.
Fill fuel tank.
2. Engine not “CHOKED” properly.
2.
See “TO START ENGINE” in Operation section.
3. Engine flooded.
3.
Wait several minutes before attempting to start.
4. Dirty air cleaner.
4.
Clean or replace air cleaner cartridge.
5. Water in fuel.
5.
Empty fuel tank and carburetor, and refill tank with fresh
gasoline.
6. Clogged fuel tank.
6.
Remove fuel tank and clean.
7. Loose spark plug wire.
7.
Make sure spark plug wire is seated properly on plug.
8. Bad spark plug or improper gap.
8.
Replace spark plug or adjust gap.
9. Carburetor out of adjustment.
9.
Make necessary adjustments.
10. Oil soaked air filter.
10.
Replace air filter.
Hard to start
1. Throttle control not set properly.
1.
Place throttle control in “FAST” position.
2. Dirty air
cleaner.
2.
Clean or replace air cleaner cartridge.
3. Bad spark plug or improper gap.
3.
Replace spark plug or adjust gap.
4. Stale or dirty fuel.
4.
Empty fuel tank and refill with fresh gasoline.
5. Loose spark plug wire.
5.
Make sure spark plug wire is seated properly on plug.
6. Carburetor out of adjustment.
6.
Make necessary adjustments.
Loss of power
1. Engine is overloaded.
1.
Set depth stake for shallower tilling.
2. Dirty air cleaner.
2.
Clean or replace air cleaner cartridge.
3. Low oil level/dirty oil.
3.
Check oil level/change oil.
4. Faulty spark plug.
4.
Clean and regap or change spark plug.
5. Oil in fuel.
5.
Empty and clean fuel tank and refill, and clean carburetor.
6. Stale or dirty fuel.
6.
Empty fuel tank and refill with fresh gasoline.
7. Water in fuel.
7.
Empty fuel tank and carburetor, and refill tank with fresh
gasoline.
8. Clogged fuel tank.
8.
Remove fuel tank and clean.
9. Spark plug wire loose.
9.
Connect and tighten spark plug wire.
10. Dirty engine air screen.
10.
Clean engine air screen.
11. Dirty/clogged muffler.
11.
Clean/replace muffler.
12. Carburetor out of adjustment.
12.
Make necessary adjustments.
13. Poor compression.
13.
Contact an authorized service center/department.
Engine overheats
1. Low oil level/dirty oil.
1.
Check oil level/change oil.
2. Dirty engine air screen.
2.
Clean engine air screen.
3. Dirty engine.
3.
Clean cylinder fins, air screen, and muffler area.
4. Partially plugged muffler.
4.
Remove and clean muffler.
5. Improper carburetor adjustment.
5.
Adjust carburetor to richer position.
Excessive bounce/
1. Ground too dry and hard.
1.
Moisten ground or wait for more favorable soil
difficult handling
conditions.
Soil balls up or clumps
1. Ground too wet.
1.
Wait for more favorable soil conditions.
Engine runs but
tiller
1. Drive control bar is not engaged.
1.
Engage drive control.
won’t
move
2. V-belt not correctly adjusted.
2.
Inspect/adjust V-belt.
3. V-belt is off pulley(s).
3.
Inspect V-belt.
Engine runs but
labors
1. Tilling too deep.
1.
Set depth stake for shallower tilling.
when tilling
2. Throttle control not properly adjusted.
2.
Check throttle control setting.
3. Carburetor out of adjustment.
3.
Make necessary adjustments.
Tines will not rotate
1. Shear pin(s) broken.
1.
Replace shear pin(s).
PROBLEM
CAUSE
CORRECTION
TROUBLESHOOTING POINTS