ProForm 530 User Manual - Page 8

Console Base as shown. Connect the Pulse Wire 118

Get ProForm 530 PDF manuals and user guides View all ProForm 530 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Turn the Console Base (85) upside-down; be careful not to scratch the Console Base. Remove the bands and the 5 Console Back (95) (see drawing 6) from the Console Base. Hold the ends of the Pulse Bar (110) against the Console Base as shown. Connect the Pulse Wire (118) in the Console Base to the pulse wire in the Pulse Bar (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try to connect them again. Have another person hold the Pulse Bar (110) firmly against the underside of the Console Frame (7). Attach the Pulse Bar with four Pulse Bar Screws (68) (only two are shown). Note: The Pulse Bar Screws may be preattached and may need to be removed. Firmly tighten the Screws. Be careful not to damage the wires. Attach the ring on the ground wire to the Console Frame (7) with a 1/2" Ground Screw (114). Note: There are no wires on the other side of the Pulse Bar (110). 6. Attach the Console Back (95) to the console assembly 6 with five 3/4" Screws (6). 110 85 68 114 7 118 Ground Wire 118 Console Assembly 6 6 95 7. With the help of another person, hold the console assembly near the Right Upright (82) and the left Upright (not shown). Connect the Wire Harness (83) to the wire harness in the console assembly. Make sure to connect the connectors properly (see the inset drawing); the connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try to connect them again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the excess wire harnesses back into the right handrail. Set the console assembly on the Right Upright (82) and the Left Upright (not shown). Thread two 1/4" x 1" Bolts (71) with 1/4" Star Washers (92) into each side of the console assembly. After you have started all four Bolts, tighten them. 8 7 Console Assembly 83 Right Handrail 83 6 92 71 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
8
7.
With the help of another person, hold the console as-
sembly near the Right Upright (82) and the left Upright
(not shown).
Connect the Wire Harness (83) to the wire harness in
the console assembly.
Make sure to connect the con-
nectors properly (see the inset drawing); the con-
nectors should slide together easily and snap into
place.
If the connectors do not slide together easily and
snap into place, turn one connector and try to connect
them again.
IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY BE DAM-
AGED WHEN THE POWER IS TURNED ON.
Insert the
excess wire harnesses back into the right handrail.
Set the console assembly on the Right Upright (82) and
the Left Upright (not shown). Thread two 1/4” x 1” Bolts
(71) with 1/4” Star Washers (92) into each side of the
console assembly.
After you have started all four
Bolts, tighten them.
82
Console
Assembly
83
92
71
83
7
Right Handrail
6.
Attach the Console Back (95) to the console assembly
with five 3/4” Screws (6).
95
6
Console Assembly
6
6
6
68
114
110
85
7
5.
Turn the Console Base (85) upside-down; be careful not
to scratch the Console Base. Remove the bands and the
Console Back (95) (see drawing 6) from the Console
Base. Hold the ends of the Pulse Bar (110) against the
Console Base as shown. Connect the Pulse Wire (118)
in the Console Base to the pulse wire in the Pulse Bar
(see the inset drawing).
The connectors should slide
together easily and snap into place.
If the connectors
do not slide together easily and snap into place, turn one
connector and try to connect them again.
Have another person hold the Pulse Bar (110) firmly
against the underside of the Console Frame (7). Attach
the Pulse Bar with four Pulse Bar Screws (68) (only two
are shown). Note: The Pulse Bar Screws may be preat-
tached and may need to be removed.
Firmly tighten the
Screws. Be careful not to damage the wires.
Attach the ring on the ground wire to the Console Frame
(7) with a 1/2” Ground Screw (114). Note: There are no
wires on the other side of the Pulse Bar (110).
Ground
Wire
118
118
5