ProForm 535 Uk Manual - Page 12

Trouble-shooting

Get ProForm 535 PDF manuals and user guides View all ProForm 535 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

TROUBLE-SHOOTING Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department at 0345-089009 (excluding holidays). 1. SYMPTOM: THE POWER DOES NOT TURN ON a. If an extension cord is needed, use only a 3-conductor, 14-gauge (1mm2) cord that is no longer than 1.5 meters (five feet). Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. 2. SYMPTOM: THE POWER TURNS OFF DURING USE c Tripped Reset Tripped Reset a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. c. Remove the key from the console. Reinsert the key fully into the console. d. If the treadmill still will not run, please call our Customer Service Department. 3. SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY a. Check the batteries in the console. See BATTERY INSTALLATION on page 8. Most problems are the result of drained batteries. b. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from the hood. Carefully remove the hood. Locate the Reed Switch (44) and the Magnet (45) on the left side of the Pulley (50). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm. If necessary, loosen the Screw (33), move the Reed Switch slightly, and then retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. b 3 mm 44 33 Top View 50 45 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, please call our Customer Service
Department at 0345-089009 (excluding holidays).
1. SYMPTOM: THE POWER DOES NOT TURN ON
a.
If an extension cord is needed, use only a 3-conductor, 14-gauge (1mm
2
) cord that is no longer than 1.5
meters (five feet).
Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill near the
power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit
breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department.
3. SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY
a. Check the batteries in the console. See BATTERY INSTALLATION on page 8. Most problems are the result
of drained batteries.
b. Remove the key from the console and
UNPLUG THE POWER
CORD.
Remove the screws from the hood. Carefully remove the
hood. Locate the Reed Switch (44) and the Magnet (45) on the
left side of the Pulley (50). Turn the Pulley until the Magnet is
aligned with the Reed Switch.
Make sure that the gap between
the Magnet and the Reed Switch is about 3 mm.
If necessary,
loosen the Screw (33), move the Reed Switch slightly, and then
retighten the Screw. Re-attach the hood, and run the treadmill for
a few minutes to check for a correct speed reading.
Tripped
Reset
Tripped
Reset
c
45
33
Top
View
3 mm
50
12
44
b