ProForm 620 Treadmill User Manual - Page 20

Trouble-shooting

Get ProForm 620 Treadmill PDF manuals and user guides View all ProForm 620 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

TROUBLE-SHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN THE POWER CORD on page 8.) If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets. b. Make sure that the key is fully inserted into the console. c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position. c Tripped Reset Tripped d On Position Reset PROBLEM: The power turns off during use SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. c. Unplug the power cord, wait for five minutes and then plug the power cord back in. d. Remove the key from the console. Reinsert the key fully into the console. e. Make sure that the on/off switch is in the on position. f. If the treadmill still will not run, please call our Customer Service Department. PROBLEM: The speed display on the console does not function properly SOLUTION: a. Remove the key from the console and UNPLUG THE a POWER CORD. Remove the screws from the hood and carefully remove the hood. Locate the Reed 3mm Switch (21) and the Magnet (43) on the left side of the 76 42 Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap be- 21 43 tween the Magnet and the Reed Switch is about 3 mm (1/8 in.). If necessary, loosen the Screw (76) Top and move the Reed Switch slightly. Retighten the View Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
20
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM:
The power does not turn on
SOLUTION:
a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN
THE POWER CORD on page 8.) If an extension cord is needed, use only a 3-conductor, 1mm
2
(14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with
GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
PROBLEM:
The power turns off during use
SOLUTION:
a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Unplug the power cord, wait for five minutes and then plug the power cord back in.
d. Remove the key from the console. Reinsert the key fully into the console.
e. Make sure that the on/off switch is in the on position.
f.
If the treadmill still will not run, please call our Customer Service Department.
PROBLEM:
The speed display on the console does not function properly
SOLUTION:
a. Remove the key from the console and
UNPLUG THE
POWER CORD.
Remove the screws from the hood
and carefully remove the hood. Locate the Reed
Switch (21) and the Magnet (43) on the left side of the
Pulley (42). Turn the Pulley until the Magnet is aligned
with the Reed Switch.
Make sure that the gap be-
tween the Magnet and the Reed Switch is about
3 mm (1/8 in.).
If necessary, loosen the Screw (76)
and move the Reed Switch slightly. Retighten the
Screw. Re-attach the hood, and run the treadmill for a
few minutes to check for a correct speed reading.
Tripped
Reset
Tripped
c
Reset
On
Position
d
43
21
76
3mm
Top
View
a
42