ProForm Crosswalk 325 Treadmill Canadian English Manual - Page 6

Set the Console Base 87 on the Handrails 4. Thread

Get ProForm Crosswalk 325 Treadmill PDF manuals and user guides View all ProForm Crosswalk 325 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3. Insert a Plastic Shim (9) into each side of the post on 3 the right side of the Base (38). Next, orient the Right 53 Upright (15) as shown, and insert it into the Base. Make sure that the Wire Harness (53) does not fall into the Right Upright. Be careful to avoid pinching the Wire Harness. Note: If necessary, tap the Right Upright with a rubber mallet until it is fully seated in the Base. If the Right Upright cannot be fully seated, remove the outer The holes must be on this side. Plastic Shim and then insert the Right Upright. Attach the Right Upright (15) to the Base (38) with three 1" Bolts (16) and three 1/4" Star Washers (2). Do not tighten the Bolts yet. 9 Assemble the Left Upright (not shown) in the same way. 2 16 15 2 16 38 4. Hold a Handrail Spacer (3) with the arrow between the two holes pointing upward. Thread the Wire Harness 4 (53) through the upper hole in the Handrail Spacer. Insert the Wire Harness into one of the Handrails and out of the large hole. If necessary, use needlenose pliers to pull the Wire Harness out of the hole. Hold the Handrail Spacer (3) and the right Handrail (4) against the right Upright (15). Attach the right Handrail and the Handrail Spacer with two 3" Handrail Bolts (1) and two 5/16" Star Washers (101) as shown. Do not tighten the Handrail Bolts yet. Attach the other Handrail (not shown) to the Left Upright (14) as described above. Note: There is not a Wire Harness in the Left Upright. 53 Large Hole 4 14 3 101 15 1 53 5. Attach the end of the ground wire to the small hole in the side of the right Handrail (4) with a Silver Ground Screw (113). Set the Console Base (87) on the Handrails (4). Thread four 3/4" Screws (5) into the Handrails and the Console Base. After you have started all four Screws, tighten the Screws until they are snug; do not overtighten the Screws. Insert the Wire Harness (53) through the two indicated plastic ties on the Console Base (87) and then through the hole in the bottom of the Console Base. 5 4 87 53 Ties 113 5 4 5 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
6
5
53
113
Ties
5
4
4
87
5
5.
Attach the end of the ground wire to the small hole in
the side of the right Handrail (4) with a Silver Ground
Screw (113).
Set the Console Base (87) on the Handrails (4). Thread
four 3/4” Screws (5) into the Handrails and the Console
Base. After you have started all four Screws,
tighten
the Screws until they are snug; do not overtighten
the Screws.
Insert the Wire Harness (53) through the two indicated
plastic ties on the Console Base (87) and then through
the hole in the bottom of the Console Base.
3. Insert a Plastic Shim (9) into each side of the post on
the right side of the Base (38). Next, orient the Right
Upright (15) as shown, and insert it into the Base.
Make
sure that the Wire Harness (53) does not fall into the
Right Upright. Be careful to avoid pinching the Wire
Harness.
Note: If necessary, tap the Right Upright with
a rubber mallet until it is fully seated in the Base. If the
Right Upright cannot be fully seated, remove the outer
Plastic Shim and then insert the Right Upright.
Attach the Right Upright (15) to the Base (38) with three
1” Bolts (16) and three 1/4” Star Washers (2).
Do not
tighten the Bolts yet.
Assemble the Left Upright (not shown) in the same way.
15
The holes must
be on this side.
53
9
16
2
3
2
38
16
4. Hold a Handrail Spacer (3) with the arrow between the
two holes pointing upward. Thread the Wire Harness
(53) through the upper hole in the Handrail Spacer.
Insert the Wire Harness into one of the Handrails and
out of the large hole. If necessary, use needlenose pliers
to pull the Wire Harness out of the hole.
Hold the Handrail Spacer (3) and the right Handrail (4)
against the right Upright (15). Attach the right Handrail
and the Handrail Spacer with two 3” Handrail Bolts (1)
and two 5/16” Star Washers (101) as shown.
Do not
tighten the Handrail Bolts yet.
Attach the other Handrail (not shown) to the Left Upright
(14) as described above. Note: There is not a Wire
Harness in the Left Upright.
53
Large Hole
1
14
101
4
53
3
15
4