ProForm Fusion 6.0 Lx English Manual - Page 26

Using The Leg Lever Lock

Get ProForm Fusion 6.0 Lx PDF manuals and user guides View all ProForm Fusion 6.0 Lx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

USING THE LEG LEVER LOCK When using the low pulley station, engage the Leg Lever Lock (47) onto the Leg Lever (15) tube. TIGHTENING THE CABLES A Woven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. To tighten the cables, first insert the weight pin into the middle of the weight stack. Slack can be removed from these cables in several ways: See drawing A. Remove the M10 Nylon Locknut (111) and the M10 x 50mm Bolt (106) from the indicated Pulley (43), Cable Trap (48), Half Finger Guards (46), and Pulley Plates (49). Reattach the Pulley, Cable B Trap, and Finger Guards using a hole closer to the center of the Pulley Plates. Make sure that the Cable Trap is oriented to hold the cable in the groove of the Pulley, that the Finger Guards are oriented as shown, and that the Cable and Pulley move smoothly. Adjust the top Pulley (43) in the same manner, if necessary. See drawing B. Adjust the Pulley (43) attached to the Small Pulley Plate (50) as described above. To remove more slack, tighten the M6 Nylon Locknut (103) further onto the end of the Press Cable (72). 47 15 43 111 46 48 49 46 106 43 43 50 103 72 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
26
72
50
USING THE LEG LEVER LOCK
When using the low pulley station, engage the Leg
Lever Lock (47) onto the Leg Lever (15) tube.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight
system, can stretch slightly when it is first used. If
there is slack in the cables before resistance is felt,
the cables should be tightened. To tighten the cables,
first insert the weight pin into the middle of the weight
stack. Slack can be removed from these cables in
several ways:
See drawing A. Remove the M10 Nylon Locknut (111)
and the M10 x 50mm Bolt (106) from the indicated
Pulley (43), Cable Trap (48), Half Finger Guards (46),
and Pulley Plates (49). Reattach the Pulley, Cable
Trap, and Finger Guards using a hole closer to the
center of the Pulley Plates.
Make sure that the
Cable Trap is oriented to hold the cable in the
groove of the Pulley, that the Finger Guards are
oriented as shown, and that the Cable and Pulley
move smoothly.
Adjust the top Pulley (43) in the
same manner, if necessary.
See drawing B. Adjust the Pulley (43) attached to the
Small Pulley Plate (50) as described above. To
remove more slack, tighten the M6 Nylon Locknut
(103) further onto the end of the Press Cable (72).
106
111
46
46
A
B
48
43
43
49
103
43
15
47