Pyle PEXA8000 PEXA3000 Manual 1 - Page 3

PEXA SERIES Overview PEXAseries amplifiers are our higher class amplifiers which meet the requirements from high end field. Unique diagram and SMTtechnology make the amplifiers have superior sound quality and incredible reliability. PEXAseries amplifier has full-protect function, including: . Soft start function to prevent wave-shock at switch power on . Delay function for preventing shock at switch power on . DC protection . Over-electric current protection . Cut-wave protection . Over heat protection Important Safety Instructions WARNING-using electric product, basic precautions should always be followed, including the following: (1)Read all the Important Safety Instructions before using the product (2)To reduce the risk of injury, close supervision is necessary when the product is used near children. (3)Do not use this product near water-for example, near a bathtub, washbowl, kitchen sink, in a wet basement or near a swimming pool or the like. (4)This product is capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for a long period of time at high volume or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. (5)This product should be located so that its location or position does not interfere with its proper ventilation. (6)This product should be located away from heat sources such as radiators, heat registers or other products that produce heat. (7)The product should be connected to a power supply only of the type described on the operating instructions or as marked on the product.Always ensure that a good quality mains lead is used applicable for your country. (8)If the mains fuse need be replaced, DISCONNECTTHE PRODUCTFROMTHE MAINS SUPPLY. The fuse is above the mains IEC socket, and must be replaced with a fuse of the type and rating stated on the rear panel. If a replacement fuse fails immediately, contact your local service agent. DO NOTreplace with a higher value. (9)The power-supply cord of the product should be unplugged from the outlet when left unused for a long period of time. When unplugging the power-supply cord, DO NOTpull on the cord, but grasp it is the plug. (10)Ensure the mains isolation switch is readily accessible when the product is in use. (11) Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. (12) The product should be serviced by qualified service personnel when: A.The power-supply cord or the plug has been damaged; or B. Object have fallen, or liquid has been spilled into the product; or C.The product has been exposed to rain; or D.The product does not appear to operate normally or exhibits a marked change in performance; or E.The product has been dropped or the enclosure damaged. (13) DO NOTattempt to service the product beyond that described in the user maintenance instructions.All other servicing should be referred to qualified service personnel. (14) WARNING-DO NOT place objects on the product s power cord or place it in a position where anyone could trip over, walk on or roll anything over it. DO NOT allow the product to rest on or to be installed over power cords of any type. Improper installations of this type create the possibility of fire hazardand/or personal injury. Page 2 PEXA SERIES Technical Specifications Model Stereo Mode (Both channels driven) 1KHz Bridge Mono Mode 1KHz 4 Ohms 8 Ohms 8 Ohms FREQUENCY RESPONSE PEXA 3000 250W X 2 150W X 2 500W PEXA 5000 500W X 2 350W X 2 1000W 10 Hz~50 Khz -1.5 dB PEXA 8000 1200W X 2 800W X 2 2400W INPUT IMPEDANCE S/N ratio (full power at 4Ù) CROSSTALK (full power at 4Ù) DAMPING FACTOR (1kHz at 4Ù) THD+N (rated power, 4Ù/1kHz) SLEW RATE PROTECTIONS CONTROLS 10kÙ Unbalanced/ 20kÙ Balanced >90dB >100dB >110dB >80dB >80dB >80dB >350 >350 >600 65V/us Full short circuit, open circuit, thermal, ultrasonic, and RF protection stable into reactive or mismatched loads, turn ON/OFF muting, tried crowbar,Limter,DC protection,soft start Front: AC switch, Input level control for each channel,Load selector Rear: Mode selector switch, Ground selector,LIMITER ON/OFF switch, COOLING Variable speed DC fans LED INDICATORS (per channel) Protect,Clip,Signal IDLE CURRENT DRAW (120V) 0.5A 0.5A 1.4A POWER SUPPLY Available for 110-120 V or 220~240 V AC, 50/60 Hz DIMENSIONS 482(W)X350(D)X88(H)mm 482(W)X410(D)X88(H)mm GROSS WEIGHT 10.5kg 13.5kg 26.5kg NET WEIGHT 10kg 13kg 26kg Page 7