Pyle PT4001X PT1201X Manual 1 - Page 5
PYLE PRO Audio, Inc., 63rd Street, Brooklyn, NY 11204
![]() |
View all Pyle PT4001X manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
Connecting to standard AC power After making all other connections, set the POWER switch to OFF position. Then connect the power cord to a standard AC outlet. Mounting the amplifier This amplifier is designed to accept standard rack mounting installations. Two slots on each end of the front panel make it suitable for such an installation. Tightly secure four mounting screws (not supplied) through these fours slots and into your standard electronics equipment rack. Turning the amplifier on 1. Turn on the audio input source equipment which is connected to the amplifier INPUT jacks. 2. Set the amplifier's Channel 1 and Channel 2 output level gain controls to the minimum level settings. 3. Push in the power switch to turn the amplifier on. Using the power blue LED meters (without PT1201X) The meter pointer position indicates the amplifier output power. For ease of reading in dark environments, the meter is illuminated. Caring for your Pyle Pro Amplifier Your Pyle Pro Amplifier is an example of superior design and craftsmanship. The following suggestions will help you care for your amplifier so you can enjoy years of use: • Keep the amplifier dry. If it gets wet, wipe immediately. • Use the amplifier only in well-ventilated installations. • Handle the amplifier gently and carefully - do not drop! • Keep the amplifier away from dust and dirt. • Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemicals, solvents or detergents! Using the Channel 1 and Channel 2 Output Level controls Rotate output level gain clockwise to increase, or counterclockwise to decrease the output power. To get the best performance with the least sound distortion, always adjust the output level gain so the meter's pointer does not continuously exceed the extreme right of the meter's scale. CAUTION: It is possible to overdrive the amplifier by setting output level gain too high, which may cause damage or failure. About the internal clip circuitry (without PT-1201X/1601X/2001X) Special clip circuitry incorporated into your Pyle Pro amplifier's design protects the amplifier and speaker system from being damaged from overdriving power. Under normal conditions, the amplifier's clip indicator will flicker as the output power momentarily exceeds the level as set by the output level gain selector. However, under excessive output conditions, the clip indicator lights remain on continuously, alerting you that the special clip circuitry has become active. When this occurs, you should simply reduce the output power level by rotating the Master Volume control counterclockwise. Amplifier Specifications Input Impedance, balanced (unbalanced) Continuous Output Power Stereo Mode 20 Hz to 20 kHz, 8 Ohms 1 kHz, 4 Ohms Maximum Power, 8 Ohms Maximum Power, 4 Ohms Peak Power, 8 Ohms Bridged Mode 20 Hz to 20 kHz, 8 Ohms 1 kHz, 8 Ohms Peak Power THD at rated output power Frequency Response +/- 3 dB Input Sensitivity for rated output power Signal-to-Noise Ratio A-Weighted Speaker Impedance Stereo Bridged Power Requirement Dimensions H x W x D, inches (mm) Weight, lbs (kg) PT-1201X 20 k-Ohms (10 k-Ohms) PT-1601X 20 k-Ohms (10 k-Ohms) PT-2001X 20 k-Ohms (10 k-Ohms) PT-4001X 20 k-Ohms (10 k-Ohms) 70W x 2 110W x 2 100W x 2 130W x 2 700W x 2 120W x 2 170W x 2 160W x 2 210W x 2 1100W x 2 170W x 2 230W x 2 220W x 2 260W x 2 1650W x 2 175W x 1 200W x 1 1400W x 1 0.1% 10 Hz to 50 kHz 1.0V 100 dB 270W x 1 320W x 1 2200W x 1 0.1% 10 Hz to 50 kHz 1.0V 100 dB 380W x 1 440W x 1 3300W x 1 0.1% 10 Hz to 50 kHz 1.0V 100 dB 4-16 Ohms 8-16 Ohms 3 7/16 x 19 x 10 3/4 (88 x 482 x 273) 18.7 (8.5) 4-16 Ohms 8-16 Ohms 4-16 Ohms 8-16 Ohms 120 VAC, 60 Hz / 230 VAC, 50 Hz 5 3/16 x 19 x 12 (132 x 482 x 304) 5 3/16 x 19 x 12 (132 x 482 x 304) 22.88 (10.4) 24.64 (11.2) 260W x 2 400W x 2 300W x 2 450W x 2 2750W x 2 700W x 1 800W x 1 5500W x 1 0.1% 10 Hz to 50 kHz 1.0V 100 dB 4-16 Ohms 8-16 Ohms 120 VAC, 60 Hz 5 3/16 x 19 x 13 (132 x 482 x 330) 33 (15) Place Stamp Here PYLE PRO Audio, Inc. 1600 63rd Street Brooklyn, NY 11204 PYLE PRO PT-1201X/1601X/2001X/4001X Amplifier Owner's Manual - 6 7 - PYLE PRO PT-1201X/1601X/2001X/4001X Amplifier Owner's Manual
![](/manual_guide/products/pyle-pt1201x-pt1201x-manual-1-6fd758f/5.png)