RCA 27V570T User Guide & Warranty - Page 39

Noisy stereo reception, No sound, picture okay

Get RCA 27V570T - 27inch Color TV PDF manuals and user guides
UPC - 034909212165
View all RCA 27V570T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Other Information • Electronic protection circuit may have been activated because of a power surge. Wait 30 seconds and then turn on again. If this happens frequently, the voltage in your house may be abnormally high or low. • Unplug TV. Wait five minutes. Plug it in again. TV turns on unexpectedly • Wake-up timer might have been activated. Go to page 32 for instructions. • You might have pressed CH+, CH- or OK on the remote accidentally. Blank screen • Make sure you have connected the component to the TV correctly. • Make sure the component connected to the TV's turned on and the TV's tuned to the corresponding video input channel. • Try another channel. No sound, picture okay • Maybe the sound is muted. Try pressing the volume up button to restore sound. • Make sure the audio cables are fully connected to the AUDIO input jacks. • If using S-Video or Y, PB, PR, remember to also connect the component's left and right audio output jacks to the TV's AUDIO input jacks. • Make sure the Int. Speakers option in the SOUND menu is turned on. Can't select certain channel • Channel may be blocked or not approved through the V-Chip. • If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR). Noisy stereo reception • May be a weak station. Access the SOUND menu, highlight Sound Type and then choose Mono. No picture/blue screen, no sound but TV is on • Maybe the signal type is set wrong. Go to page 31 for detailed instructions. • The channel might be blank - change channels. • If you're watching your VCR and it's connected with a coaxial cable to the TV ANT jack, tune the TV to channel 3 or 4 (whichever channel is selected on the 3/4 switch on the back of your VCR). Also check to make sure the TV/VCR button on the VCR is in the correct mode (press the TV/VCR button on your VCR). Sound okay, picture poor • Check antenna and video connections. Make sure all of the cables are firmly connected to the jacks. • Try adjusting the sharpness function to improve weak signals. Go to page 30 for more instructions. Black box appears on the screen • Closed-captioning might be on. Check Closed Caption in the Setup menu. Go to page 31 for more instructions. PASSWORD menu appears • KidPass option is activated and you try to reset the time. • You turn the TV on after KidPass shut off the TV. Chapter 5 Graphics contained within this publication are for representation only. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Chapter 5
35
Graphics contained within this publication are for representation only.
Other Information
•
Electronic protection circuit may have been activated because of a power surge.
Wait
30 seconds and then turn on again.
If this happens frequently, the voltage in your
house may be abnormally high or low.
•
Unplug TV. Wait five minutes. Plug it in again.
TV turns on unexpectedly
•
Wake-up timer might have been activated. Go to page 32 for instructions.
•
You might have pressed CH+, CH- or OK on the remote accidentally.
Blank screen
•
Make sure you have connected the component to the TV correctly.
•
Make sure the component connected to the TV’s turned on and the TV’s tuned to the
corresponding video input channel.
•
Try another channel.
No sound, picture okay
•
Maybe the sound is muted.
Try pressing the volume up button to restore sound.
•
Make sure the audio cables are fully connected to the AUDIO input jacks.
•
If using S-Video or Y, P
B
, P
R
, remember to also connect the component’s left and right
audio output jacks to the TV’s AUDIO input jacks.
•
Make sure the
Int. Speakers
option in the
SOUND
menu is turned on.
Can’t select certain channel
•
Channel may be blocked or not approved through the V-Chip.
•
If using a VCR, check to make sure the TV/VCR button on the VCR is in the correct
mode (press the TV/VCR button on your VCR).
Noisy stereo reception
•
May be a weak station. Access the
SOUND
menu, highlight
Sound Type
and then
choose
Mono
.
No picture/blue screen, no sound but TV is on
•
Maybe the signal type is set wrong. Go to page 31 for detailed instructions.
•
The channel might be blank — change channels.
•
If you’re watching your VCR and it’s connected with a coaxial cable to the TV ANT jack,
tune the TV to channel 3 or 4 (whichever channel is selected on the 3/4 switch on the
back of your VCR). Also check to make sure the TV/VCR button on the VCR is in the
correct mode (press the TV/VCR button on your VCR).
Sound okay, picture poor
•
Check antenna and video connections. Make sure all of the cables are firmly connected
to the jacks.
•
Try adjusting the sharpness function to improve weak signals. Go to page 30 for more
instructions.
Black box appears on the screen
•
Closed-captioning might be on. Check
Closed Caption
in the
Setup
menu. Go to page
31 for more instructions.
PASSWORD menu appears
•
KidPass option is activated and you try to reset the time.
•
You turn the TV on after KidPass shut off the TV.