RCA 75400 User Manual - 75400 - Page 5

Getting Started, First Things First

Page 5 highlights

First Things First CABINET OVERHANG WASHER CABINET BOTTOM EN SPACERS EQUAL TO OR LONGER THAN CABINET OVERHANG 3/8" MINIMUM 3/4" MAXIMUM 8. Extend cord towards electrical outlet and secure by using the Cord Hooks to hold cord out of the way. For most attractive appearance, place Cord Hooks at back edge of cabinet (on or next to wall) directly over outlet to be used. To attach Cord Hooks, peel off adhesive back and attach to a clean, dry surface on underside of cabinet or back wall. Plug Cord into 120-volt AC electrical outlet. We recommend that the line cord be fully extended for best FM reception. SELECTED SCREWS WHICH MEET MINIMUM, BUT DO NOT EXCEED MAXIMUM LENGHT. 5. Insert screws FROM INSIDE THE CABINET. The washers must be used on metal cabinets, and on wood cabinets if you did not countersink the drilled holes. Position washers, flat side down, and place screws into the holes. If your cabinet does not have an overhang, go to Step 7. 6. Hold screw heads down while you push the selected spacers onto the screws under the cabinet. Be sure to push up spacers until they are firmly against the cabinet bottom and/or fully nested (if more than one is used). 7. Align radio under the screws. Hold the screw holes in the top of the clock radio against the mounting screws and partially tighten the screws. Do not fully tighten until all 3 screws have been started. (The top front edge of the clock radio should clear the overhang.) COMPACT DISC PLAYER CLOCK/TIMER DISPLAY A OF RADI C TIMER ON/SET OF Spacemaker STERE Compact DIsc Player AM/FM Stereo High Performance Sub-woofer F 85 92 96 100 104 108 MH HOU MINUT SE A 530 650 800 1000 1300 1700 kHz STO PLAY/PAUS TRAC SEARC REPEA SHUFFL Getting Started Automatic Time Set Selecting Time Zone The Time Zone switch is located in the battery compartment on the side of the unit. Open the compartment door by rotating the lock in the direction of the arrow . Daylight Saving Time (DST) After selecting time zone and plugging in your unit, daylight saving time must be activated for those areas observing such change. The daylight saving button is located in the EN battery compartment on the side of the unit. Press and hold the DAYLIGHT SAVING button until the icon lights on the display. To disable daylight saving time, press and hold again until the icon no longer lights. ! Warning: Please avoid playing with these buttons after entering the Clock set mode. TIME ZONE - Slide the switch to select time zone. Refer to Figure 1 for U.S. Time Zone details. Refer to Figure 2 for Canadian Time Zone details. Select 1 for Eastern Daylight Time Select 2 for Central Daylight Time Select 3 for Mountain Daylight Time Select 4 for Pacific Daylight Time Note: oC/oF, ID and RESET- refer to Thermometer function. ALTITUDE - refer to Weather Forecast function. - refer to Clock & Timer. 5 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12

EN
EN
Automatic Time Set
Selecting Time Zone
The Time Zone switch is located in the battery
compartment on the side of the unit.
Open the compartment door by rotating the
lock in the direction of the arrow
.
TIME ZONE
- Slide the switch to select time
zone.
Refer to Figure 1 for U.S. Time Zone details.
Refer to Figure 2 for Canadian Time Zone
details.
Select 1 for Eastern Daylight Time
Select 2 for Central Daylight Time
Select 3 for Mountain Daylight Time
Select 4 for Pacific Daylight Time
Daylight Saving Time (DST)
After selecting time zone and plugging in your
unit, daylight saving time must be activated for
those areas observing such change.
The daylight saving button is located in the
battery compartment on the side of the unit.
Press and hold the DAYLIGHT SAVING
button
until the icon lights on the display.
To disable daylight saving time, press and hold
again until the icon no longer lights.
Getting Started
Warning:
Please avoid playing with these
buttons after entering the Clock set
mode.
6
Note:
o
C/
o
F
,
ID
and
RESET
- refer to Thermometer
function.
ALTITUDE -
refer to Weather Forecast
function.
- refer to Clock & Timer.
!
First Things First
5
EQUAL TO OR
LONGER THAN
CABINET
OVERHANG
3
/
8
" MINIMUM
3
/
4
" MAXIMUM
CABINET
OVERHANG
CABINET
BOTTOM
WASHER
SPACERS
SELECTED SCREWS WHICH MEET MINIMUM,
BUT DO NOT EXCEED MAXIMUM LENGHT.
5.
Insert screws FROM INSIDE THE CABINET. The
washers must be used on metal cabinets, and
on wood cabinets if you did not countersink
the drilled holes. Position washers, flat side
down, and place screws into the holes.
If your cabinet does not have an
overhang, go to Step 7.
6.
Hold screw heads down while you push the
selected spacers onto the screws under the
cabinet. Be sure to push up spacers until they
are firmly against the cabinet bottom and/or
fully nested (if more than one is used).
7.
Align radio under the screws. Hold the screw
holes in the top of the clock radio against the
mounting screws and partially tighten the
screws.
Do not fully tighten until all 3 screws have
been started. (The top front edge of the clock
radio should clear the overhang.)
8.
Extend cord towards electrical outlet and
secure by using the Cord Hooks to hold cord
out of the way. For most attractive
appearance, place Cord Hooks at back edge
of cabinet (on or next to wall) directly over
outlet to be used. To attach Cord Hooks, peel
off adhesive back and attach to a clean, dry
surface on underside of cabinet or back wall.
Plug Cord into 120-volt AC electrical outlet.
We recommend that the line cord be fully
extended for best FM reception.