Rheem H95 Outdoor Series Use and Care Manual - Page 59

Remote Control Installation

Get Rheem H95 Outdoor Series PDF manuals and user guides View all Rheem H95 Outdoor Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

INSTALLATION INSTRUCTIONS Remote Control Installation WARNING:Fieldwiringconnectionsand electricalgroundingmustcomplywithlocalcodesor, intheabsenceoflocalcodes,withthelatestedition oftheNationalElectricalCode,ANSI/NFPA70,orin  Canada,CanadianElectricalCode,CAN/CSAC22.1, Part1. NOTICES: •RemotecontrolcablecanbeanyType-T18AWGwire similartoathermostatwireandneednotbepolaritysensitive. •Itisnotrecommendedtohavewiringexposed. •Donotapplysealanttoremotecontrolcable. •Donotusenetworkcable,telephonewire,orany twisted-paircable. ConnectingtheMAIN(UMC-117)RemoteControltoa Wall: 4  Installthebaseplatetothewallusingsuitable screwsandwallanchors.  NOTICE:Thetabsonthebaseplateshould alwayspointout. 5  Connecttheremotecontroltotheremotecontrol cable. 1  Drilla1-to11/2-in.(2.5/3.8-cm)holeatthe proposedcontrollocation.Installtheremote controlcablebetweenthelocationoftheremote controlandthewaterheater. 2  Removetheremotecontrolfromthebaseplate. 6  Positiontheremotecontrolonthebaseplate. NOTICE:  Thetabsonthebaseplateshould lineupwiththeslotsonthebackofthecontrol panel.  Securethecontrolpaneltothebaseplatewithone screwintothebottomtab. NOTICE:Donotattempttoconnecttheremote controlorcontrolwiretothewaterheaterwhilethe waterheaterhaspowerappliedtoit.Damagetothe waterheaterwilloccur.Donotcutorstripthewiring whileitisconnectedtothewaterheaterorwhilethe waterheaterhaspowerappliedtoit. Electrical 3  Feedtheremotecontrolcablethroughthelarge centerholeinthebaseplate. 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
59
INSTALLATION INSTRUCTIONS
Remote Control Installation
WARNING:
±Field±wiring±connections±and±
electrical±grounding±must±comply±with±local±codes±or,±
in±the±absence±of±local±codes,±with±the±latest±edition±
of±the±National±Electrical±Code,±ANSI/NFPA±70,±or±in±
Canada,±Canadian±Electrical±Code,±CAN/CSA±C22.1,±
Part±1.
±
NOTICES:
•±±
Remote±control±cable±can±be±any±Type–T±18±AWG±wire±
similar±to±a±thermostat±wire±and±need±not±be±polarity-
sensitive.
•±±
It±is±not±recommended±to±have±wiring±exposed.
•±±
Do±not±apply±sealant±to±remote±control±cable.
•±±
Do±not±use±network±cable,±telephone±wire,±or±any±
twisted-pair±cable.
Connecting±the±MAIN±(UMC-117)±Remote±Control±to±a±
Wall:±
±
Drill±a±1-±to±1±1/2-in.±(2.5/3.8-cm)±hole±at±the±
proposed±control±location.±Install±the±remote±
control±cable±between±the±location±of±the±remote±
control±and±the±water±heater.
±
Remove±the±remote±control±from±the±base±plate.
±
Feed±the±remote±control±cable±through±the±large±
center±hole±in±the±base±plate.
±
Install±the±base±plate±to±the±wall±using±suitable±
screws±and±wall±anchors.
± NOTICE:
±The±tabs±on±the±base±plate±should±
always±point±out.
±
Connect±the±remote±control±to±the±remote±control±
cable.
±
Position±the±remote±control±on±the±base±plate.
±
NOTICE:
±The±tabs±on±the±base±plate±should±
line±up±with±the±slots±on±the±back±of±the±control±
panel.
±
Secure±the±control±panel±to±the±base±plate±with±one±
screw±into±the±bottom±tab.
NOTICE:
±Do±not±attempt±to±connect±the±remote±
control±or±control±wire±to±the±water±heater±while±the±
water±heater±has±power±applied±to±it.±Damage±to±the±
water±heater±will±occur.±Do±not±cut±or±strip±the±wiring±
while±it±is±connected±to±the±water±heater±or±while±the±
water±heater±has±power±applied±to±it.
2
4
5
6
1
3
Electrical