Rocketfish RF-WS01 User Manual (English) - Page 15

Using your system - troubleshooting

Get Rocketfish RF-WS01 PDF manuals and user guides View all Rocketfish RF-WS01 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Using your system Turning on your system To turn on the system: 1 Move the Power switch to the ON position on the side panel of the sender. The green Link Status LED starts to blink slowly to indicate the sender is plugged in and in Standby mode. 2 Press the Power switch on the front panel of the speakers. The green Status LED starts to flash to indicate the receiver is plugged in and in Standby mode. Note: If the speaker is operated by batteries and battery capacity is too low to power the speakers, the Low Battery Warning LED turns red to indicate a low battery warning. The sender and speakers were pre-paired in the factory. When an active link is established between them the green Link Status LEDs turn solid. Note: If the LEDs continue to blink after 30 seconds, it means there is no active link between the sender and speakers. Try to connect the system manually using the PAIR button. For more information see "Troubleshooting" on page 17. Listening to your system To listen to the system: 1 Turn on the system. Make sure that there is an active link between the sender and speakers. When an active link is established between them the green Link Status LEDs turn solid. 2 Turn on your audio source, then play the audio. To adjust the volume on the RF-WS01 or RF-WS01-W: • Turn the volume knob on the speaker. The volume is adjusted independently regardless of channel setting (left, right, or mono). To adjust the volume on the RF-WS02: • Turn the volume knob on the speaker. Make sure the speaker is switched to the correct left, right, or mono setting for speaker output sound. RF-WS01/WS01-W/WS02 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
15
RF-WS01/WS01-W/WS02
Using your system
Turning on your system
To turn on the system:
1
Move the Power switch to the ON position on the side panel of the
sender. The green Link Status LED starts to blink slowly to indicate the
sender is plugged in and in Standby mode.
2
Press the Power switch on the front panel of the speakers. The green
Status LED starts to flash to indicate the receiver is plugged in and in
Standby mode.
Note:
If the speaker is operated by batteries and battery capacity is too low to power
the speakers, the Low Battery Warning LED turns red to indicate a low battery
warning.
The sender and speakers were pre-paired in the factory. When an active
link is established between them the green Link Status LEDs turn solid.
Note:
If the LEDs continue to blink after 30 seconds, it means there is no active link
between the sender and speakers. Try to connect the system manually using the PAIR
button. For more information see “Troubleshooting” on page 17.
Listening to your system
To listen to the system:
1
Turn on the system. Make sure that there is an active link between the
sender and speakers. When an active link is established between them
the green Link Status LEDs turn solid.
2
Turn on your audio source, then play the audio.
To adjust the volume on the RF-WS01 or RF-WS01-W:
•
Turn the volume knob on the speaker. The volume is adjusted
independently regardless of channel setting (left, right, or mono).
To adjust the volume on the RF-WS02:
•
Turn the volume knob on the speaker. Make sure the speaker is switched
to the correct left, right, or mono setting for speaker output sound.