Ryobi TSS702 Operation Manual - Page 4
Miter Saw Specific Safety Rules, Additional Safety Rules - manual
View all Ryobi TSS702 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
MITER SAW SPECIFIC SAFETY RULES Do not use another person as a substitute for a table extension or as additional support. Unstable support for the workpiece can cause the blade to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade. The cut-off piece must not be jammed or pressed by any means against the spinning saw blade. If confined, i.e. using length stops, the cut-off piece could get wedged against the blade and thrown violently. Always use a clamp or a fixture designed to properly support round material such as rods or tubing. Rods have a tendency to roll while being cut, causing the blade to bite and pull the work with your hand into the blade. Let the blade reach full speed before contacting the workpiece. This will reduce the risk of the workpiece being thrown. If the workpiece or blade becomes jammed, turn the miter saw off. Wait for all moving parts to stop and disconnect the plug from the power source and/ or remove the battery pack. Then work to free the jammed material. Continued sawing with a jammed workpiece could cause loss of control or damage to the miter saw. After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop before removing the cut-off piece. Reaching with your hand near the coasting blade is dangerous. Hold the handle firmly when making an incomplete cut or when releasing the switch before the saw head is completely in the down position. The braking action of the saw may to be suddenly pulled downward, causing a risk of injury. Save these instructions. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also. ADDITIONAL SAFETY RULES Use the proper extension cord. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Inspect tool cords periodically. If damaged, have repaired by a qualified service technician at an authorized service facility. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade. Inspect extension cords periodically and replace if damaged. Polarized plugs. To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Know your power tool. Read the operator's manual carefully. Learn the applications and limitations as well as the specific potential hazards related to this tool. Always wear eye protection with side shields which is marked to comply with ansi Z87.1 when using this product. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. Never stand on tool. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. Keep guards in place and in good working order. Use the right direction of feed. Feed work into a blade, cutter, or sanding spindle against the direction of rotation of the blade, cutter, or sanding spindle only. Never leave tool running unattended. Turn the power off. Don't leave tool until it comes to a complete stop. Use only correct blades. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 7-1/4 in. Before making a cut, be sure all adjustments are secure. Never touch blade or other moving parts during use. Double check all setups. Make sure blade is tight and not making contact with saw or workpiece before connecting to power supply. Firmly clamp or bolt your tool to a workbench or table at approximately hip height. Make sure the miter table and saw arm (bevel function) are locked in position before operating your saw. Lock the miter table by pushing the miter lock lever down. Lock the saw arm (bevel function) by securely tightening the bevel lock knob. 4 − English