Samsung DV52J8700EW/A2 User Manual - Page 11

Ducting requirements

Get Samsung DV52J8700EW/A2 PDF manuals and user guides View all Samsung DV52J8700EW/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Before installation Ducting requirements Recommended Use only for short-run installation Weather hood type No. of 90° elbows 0 1 2 3 4" (10.2 cm) Rigid Metallic flexible* 80 ft. (24.4 m) 41 ft. (12.4 m) 68 ft. (20.7 m) 37 ft. (11.2 m) 57 ft. (17.4 m) 33 ft. (10.1 m) 47 ft. (14.3 m) 29 ft. (8.8 m) 2.5" (6.4 cm) Rigid Metallic flexible* 74 ft. (22.6 m) 33 ft. (10.1 m) 62 ft. (18.9 m) 29 ft. (8.8 m) 51 ft. (15.5 m) 25 ft. (7.6 m) 41 ft. (12.5 m) 21 ft. (6.5 m) NOTE * Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct. If you integrate the dryer's vent system with an existing exhaust system, make sure: • The exhaust system meets all applicable local, state, and national regulations. • Not to use a flexible plastic duct. • To regularly check and clean all lint buildup from inside the existing ducts. • The duct is not kinked or crushed. • The exhaust hood damper opens and closes freely. Manometer measurements The static pressure in any exhaust system must not exceed 0.83 inches of water column or be less than 0. Note that these values are measured with the dryer running with a manometer presented to the exhaust duct that connects to the dryer. The dryer tumbler must be empty and lint filter clean. %7+4@&/64JOEE English 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Before installation
English
11
Ducting requirements
Recommended
Use only for short-run installation
Weather hood
type
4” (10.2 cm)
2.5” (6.4 cm)
No. of 90°
elbows
Rigid
Metallic
flexible*
Rigid
Metallic
flexible*
0
80 ft. (24.4 m)
41 ft. (12.4 m)
74 ft. (22.6 m)
33 ft. (10.1 m)
1
68 ft. (20.7 m)
37 ft. (11.2 m)
62 ft. (18.9 m)
29 ft. (8.8 m)
2
57 ft. (17.4 m)
33 ft. (10.1 m)
51 ft. (15.5 m)
25 ft. (7.6 m)
3
47 ft. (14.3 m)
29 ft. (8.8 m)
41 ft. (12.5 m)
21 ft. (6.5 m)
NOTE
* Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.
If you integrate the dryer’s vent system with an existing exhaust system, make
sure:
•
The exhaust system meets all applicable local, state, and national regulations.
•
Not to use a flexible plastic duct.
•
To regularly check and clean all lint buildup from inside the existing ducts.
•
The duct is not kinked or crushed.
•
The exhaust hood damper opens and closes freely.
Manometer measurements
The static pressure in any exhaust system must not exceed 0.83 inches of water column
or be less than 0. Note that these values are measured with the dryer running with a
manometer presented to the exhaust duct that connects to the dryer. The dryer tumbler
must be empty and lint filter clean.
DV8000J-03170S-03_EN-US.indd
11
2015/9/14
15:20:44