Samsung NA30N6555TG/AA Installation Guide - Page 15

English 15, Hold down bracket install guide

Get Samsung NA30N6555TG/AA PDF manuals and user guides View all Samsung NA30N6555TG/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Correct installation Front of unit Hold down bracket holes 1. Locate electrical outlet and gas shut-off valve beneath cabinet. 2. Apply the foam tape around the edge of the cutout opening. Do not overlap the foam strips. • The foam strip helps avoid damage to the underside of the cooktop from debris and helps the cooktop sit flat on uneven counters. 3. Protect surface of cooktop • Place a towel or tablecloth onto the countertop. 4. With bottom side first, gently put the cooktop down. Then, slightly lift up the rear to remove the protective rubber for the Wi-Fi module. • Make sure the front of the countertop is parallel to the cooktop • Make final check that all required clearances are met. 5. Secure the cooktop to the countertop using the two provided hold-down brackets as shown. Hold down bracket install guide Case 1. Countertop Chassis Side wall of undercounter cabinet Case 2. Chassis Countertop M4 L10 screw M4 L16 screw Hold down bracket M4 L10 screw W3/16 L75 screw Hold down bracket NOTE Smart Connect module can/must be detached before installation of the cooktop in folowing cases: • The consumer doesn't need to Smart connect function. • Installation is not possible because the Smart Connect module protrudes against the rear wall of the countertop. • The downdraft hood is installed and protrudes against the Smart Connect module. The Cover must be installed in place of Smart connect module if Smart connect module has been removed. Please read following instructions on how to detach Smart connect module. Power cord Gas inlet Hold Down Bracket Installation Installation instructions English 15 Install_NA30N6555TG_DG68-01091A-02_EN+MES+CFR.indb 15 10/24/2018 4:29:17 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
English 15
Installation instructions
1.
Locate electrical outlet and gas shut-off
valve beneath cabinet.
2.
Apply the foam tape around the edge of
the cutout opening. Do not overlap the
foam strips.
•
The foam strip helps avoid damage
to the underside of the cooktop from
debris and helps the cooktop sit flat on
uneven counters.
3.
Protect surface of cooktop
•
Place a towel or tablecloth onto the
countertop.
Correct installation
4.
With bottom side first, gently put the
cooktop down. Then, slightly lift up the
rear to remove the protective rubber for
the Wi-Fi module.
•
Make sure the front of the countertop is
parallel to the cooktop
•
Make final check that all required
clearances are met.
Front of unit
Gas inlet
Power cord
Hold Down Bracket Installation
Hold down
bracket holes
5.
Secure the cooktop to the countertop
using the two provided hold-down
brackets as shown.
Hold down bracket install guide
M4 L10 screw
M4 L16 screw
Case 1.
Countertop
Side wall of
undercounter
cabinet
Hold down
bracket
W
3
/
16
L75 screw
Case 2.
Countertop
Chassis
Hold down
bracket
Chassis
M4 L10 screw
NOTE
Smart Connect module can/must be detached before installation of the cooktop in
folowing cases:
•
The consumer doesn’t need to Smart connect function.
•
Installation is not possible because the Smart Connect module protrudes against
the rear wall of the countertop.
•
The downdraft hood is installed and protrudes against the Smart Connect
module.
The Cover must be installed in place of Smart connect module if Smart connect
module has been removed. Please read following instructions on how to detach
Smart connect module.
Install_NA30N6555TG_DG68-01091A-02_EN+MES+CFR.indb
15
10/24/2018
4:29:17 PM