Samsung R7260 User Manual - Page 31

Troubleshooting

Get Samsung R7260 PDF manuals and user guides View all Samsung R7260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Troubleshooting Symptom The POWERbot is not working at all. The POWERbot has stopped during cleaning. Suction power is weak. The POWERbot cannot find the docking station. The POWERbot suddenly cleans diagonally. POWERbot does not detect the boundary marker and crosses the boundary. Checklist ffCheck if the emergency switch is on. ffCheck if all the icons are displayed on the display panel. ffCheck if the POWERbot's battery is depleted. --When "Lo" is displayed, place the POWERbot on the docking station to charge it. ffReplace the batteries (AAA type) if the remote controller is not working. ffWhen "Lo" is displayed on the display panel, place the POWERbot on the docking station to charge it. ffWhen POWERbot is immobilized by an obstacle such as a cord, threshold etc, pick it up and move it away from the obstacle. --If any fabric or string is caught in a drive wheel, turn off the emergency switch and remove the fabric or string before using it again. ffWhen there's too much dust in the dustbin, suction power may get weakened. Turn off the emergency switch and empty the dustbin. ffIf the brush is blocked by foreign matter, turn off the emergency switch and remove foreign matter from the brush. ffWhen noise suddenly increase, turn off the emergency switch and empty the dustbin. ffCheck if there's a power failure or whether the power plug is unplugged. ffRemove any obstacles around the docking station that may prevent POWERbot from returning to the docking station. ffWhen there's foreign matter on the charging pins, charging can be affected. Clean the foreign matter off the pins. ffCheck if the docking station is installed along the grain of wooden floors or tiles. ffThe POWERbot may clean in a diagonal direction if it is moving to another area using the shortest route. It may also move at a diagonal if it made contact with an obstacles at that angle, if it was charged at the docking station at an angle, or if the grain of the wooden/tile floor skewed is in that direction. ffMake sure the boundary markers are attached as ( ) shape at 15 cm before the locations where the POWERbot shouldn't cross. 1_VR7200_EN_DJ68-00827B-03_AA.indd 31 ENGLISH-31 2020-01-13 오전 1:13:32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
ENGLISH-
31
Troubleshooting
Symptom
Checklist
The POWERbot is not working at all.
f
Check if the emergency switch is on.
f
Check if all the icons are displayed on the display panel.
f
Check if the POWERbot's battery is depleted.
– When "Lo" is displayed, place the POWERbot on the
docking station to charge it.
f
Replace the batteries (AAA type) if the remote controller is
not working.
The POWERbot has stopped during
cleaning.
f
When "Lo" is displayed on the display panel, place the
POWERbot on the docking station to charge it.
f
When POWERbot is immobilized by an obstacle such as a
cord, threshold etc, pick it up and move it away from the
obstacle.
– If any fabric or string is caught in a drive wheel, turn off
the emergency switch and remove the fabric or string
before using it again.
Suction power is weak.
f
When there's too much dust in the dustbin, suction power
may get weakened. Turn off the emergency switch and
empty the dustbin.
f
If the brush is blocked by foreign matter, turn off the
emergency switch and remove foreign matter from the
brush.
f
When noise suddenly increase, turn off the emergency
switch and empty the dustbin.
The POWERbot cannot find the
docking station.
f
Check if there's a power failure or whether the power plug
is unplugged.
f
Remove any obstacles around the docking station that may
prevent POWERbot from returning to the docking station.
f
When there's foreign matter on the charging pins, charging
can be affected. Clean the foreign matter off the pins.
The POWERbot suddenly cleans
diagonally.
f
Check if the docking station is installed along the grain of
wooden floors or tiles.
f
The POWERbot may clean in a diagonal direction if it is
moving to another area using the shortest route. It may also
move at a diagonal if it made contact with an obstacles at
that angle, if it was charged at the docking station at an
angle, or if the grain of the wooden/tile floor skewed is in
that direction.
POWERbot does not detect the
boundary marker and crosses the
boundary.
f
Make sure the boundary markers are attached as (
)
shape at 15 cm before the locations where the POWERbot
shouldn't cross.
1_VR7200_EN_DJ68-00827B-03_AA.indd
31
2020-01-13
오전 1:13:32