Samsung SCX-5835 User Guide - Page 134

Upgrading a memory module, Checking replaceable’s lifespan

Get Samsung SCX-5835 PDF manuals and user guides View all Samsung SCX-5835 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

When installing accessories, the battery inside the machine is a service component. Do not change it by yourself. There is a risk of an explosion if battery is replaced by an incorrect type. Dispose used batteries according to the instructions. UPGRADING A MEMORY MODULE Your machine has a dual in-line memory module (DIMM). Use this memory module slot to install additional memory. The machine has two memory slots with a factory pre-installed memory module in one slot. When you are expanding the memory capacity, you can add a memory module to the vacant memory slot. It is strongly recommended that you expand a memory module in the vacant memory slot, and not by removing a pre-installed memory module. If your machine has 256 MB memory capacity and you want to add 256 MB, the memory capacity expands up to 512 MB. Order information is provided for additional memory module. (See "Available accessories" on page 140.) Installing a memory module 1. Turn the machine off and unplug all cables from the machine. 2. Grasp the control board cover and remove it. 3. Remove the new memory module from its bag. 4. Holding the memory module by the edges, align the memory module on the slot at about a 30-degree tilt. Make sure that the notches of the module and the grooves on the slot fit each other. The notches and grooves illustrated above may not match those on an actual memory module and its slot. 5. Press the memory module into the slot with care until you hear a 'click'. Do not press the memory module strongly or the module may be damaged. If the module does not seem to fit into the slot properly, carefully try the previous procedure again. 6. Close the control board cover by aligning the groove on it with the notch on the machine and sliding it. 7. Reconnect the power cord and machine cable. Turn on the machine. If you use the PS driver, you must activate the added memory in the PS driver properties. Activating the added accessories in PS printer properties After installing the memory module, you need to select it in the printer properties of the PostScript printer driver in order to use it. 1. Install the PS Driver. (See "Installing USB connected machine's driver" on page 3, "Installing network connected machine's driver" on page 2.) 2. Click the Windows Start menu. • For Windows 2000, select Settings > Printers. • For Windows XP/2003, select Printers and Faxes. • For Windows Vista, select Control Panel > Hardware and Sound > Printers. 3. Select the your machine's PS driver and right-click to open Properties. 4. Select Device Settings. 5. Select the Installable Options section and set the necessary options. 6. Click OK. CHECKING REPLACEABLE'S LIFESPAN If you experience frequent paper jams or printing problems, check the number of pages the machine has printed. Replace the corresponding parts, if necessary. 1. Press Machine Setup on the control panel. 2. Press Machine Status > the Supplies Life tab. Supplies and accessories_ 142

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
Supplies and accessories
_ 142
When installing accessories, the battery inside the machine is a
service component. Do not change it by yourself.
There is a risk of an explosion if battery is replaced by an incorrect
type. Dispose used batteries according to the instructions.
UPGRADING A MEMORY MODULE
Your machine has a dual in-line memory module (DIMM). Use this memory
module slot to install additional memory.
The machine has two memory slots with a factory pre-installed memory
module in one slot. When you are expanding the memory capacity, you can
add a memory module to the vacant memory slot. It is strongly
recommended that you expand a memory module in the vacant memory
slot, and not by removing a pre-installed memory module. If your machine
has 256 MB memory capacity and you want to add 256 MB, the memory
capacity expands up to 512 MB. Order information is provided for additional
memory module. (See "Available accessories" on page 140.)
Installing a memory module
1.
Turn the machine off and unplug all cables from the machine.
2.
Grasp the control board cover and remove it.
3.
Remove the new memory module from its bag.
4.
Holding the memory module by the edges, align the memory module on
the slot at about a 30-degree tilt. Make sure that the notches of the
module and the grooves on the slot fit each other.
The notches and grooves illustrated above may not match those
on an actual memory module and its slot.
5.
Press the memory module into the slot with care until you hear a 'click'.
Do not press the memory module strongly or the module may be
damaged. If the module does not seem to fit into the slot properly,
carefully try the previous procedure again.
6.
Close the control board cover by aligning the groove on it with the notch
on the machine and sliding it.
7.
Reconnect the power cord and machine cable. Turn on the machine.
If you use the PS driver, you must activate the added memory in the
PS driver properties.
Activating the added accessories in PS printer
properties
After installing the memory module, you need to select it in the printer
properties of the PostScript printer driver in order to use it.
1.
Install the PS Driver. (See "Installing USB connected machine’s driver"
on page 3, "Installing network connected machine’s driver" on page 2.)
2.
Click the Windows
Start
menu.
•
For Windows 2000, select
Settings
>
Printers
.
•
For Windows XP/2003, select
Printers and Faxes
.
•
For Windows Vista, select
Control Panel
>
Hardware and Sound
>
Printers
.
3.
Select the your machine’s PS driver and right-click to open
Properties
.
4.
Select
Device Settings
.
5.
Select the
Installable Options
section and set the necessary options.
6.
Click
OK
.
CHECKING REPLACEABLE’S LIFESPAN
If you experience frequent paper jams or printing problems, check the
number of pages the machine has printed. Replace the corresponding
parts, if necessary.
1.
Press
Machine Setup
on the control panel.
2.
Press
Machine Status
> the
Supplies Life
tab.