Samsung SP-A900B User Manual (user Manual) (ver.1.0) (English) - Page 10

contact your product provider or our

Get Samsung SP-A900B PDF manuals and user guides View all Samsung SP-A900B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Power Cable Remote Control/ 2 Batteries (Not available in all locations) Cleaning Cloth LED Indications :Light is On STAND BY :Light is Blinking LAMP TEMP :Light is Off Information If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. The projector is in normal operating condition. This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed. The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off the inside of the projector. (Lasts for about 1 minute and 30 seconds) Refer to Action 1 below if the cooling fan inside the projector is not in normal operation condition. Refer to Action 2 below if the lamp cover protecting the lamp unit is not closed properly. Power is turned off automatically when temperature inside of the projector goes beyond the control limit. Refer to Action 3. A problem has occurred when operating the DDP IC in the product. Refer to Action 4. A problem has occurred with the operation of the lamp. Refer to Action 5. The lifetime of the lamp has expired. Refer to Action 6. The memory in the product is not operating normally. Contact a service center. The power for the product is not operating normally. Contact a service center. A problem has occurred when operating the color wheel in the product. Refer to Action 4. Clearing Indicator Problems Classification State Action 1 When the cooling fan system is not in normal operating condition. Action 2 When the lamp cover protecting the lamp unit is not properly closed or the sensor system is not in normal operating condition. Measures If the symptom remains even after disconnecting and then reconnecting the power cord and turning the projector on again, contact your product provider or our service center. Check whether the screws at the bottom side of the projector are fastened correctly. If they are abnormally fastened, contact your product distributor or service center.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
ºower Àable
¼emote Àontrol/ 2 Batteries
(¾ot available in all locations)
Àleaning Àloth
Á½· µndications
:Áight is »n
:Áight is Blinking
:Áight is »ff
¿T¹¾· BY
Á¹Mº
T½Mº
µnformation
µf you press the º»¶½¼ button on the remote control or projector, the screen
appears within 30 seconds.
The projector is in normal operating condition.
This state appears when the projector is preparing an operation after the º»¶½¼ button
on the projector or the remote control has been pressed.
The º»¶½¼ button is pressed to turn off the projector, and the cooling system is in
operation to cool off the inside of the projector. (Áasts for about 1 minute and 30
seconds)
¼efer to ¹ction 1 below if the cooling fan inside the projector is not in normal operation
condition.
¼efer to ¹ction 2 below if the lamp cover protecting the lamp unit is not closed properly.
ºower is turned off automatically when temperature inside of the projector goes beyond
the control limit. ¼efer to ¹ction 3.
¹ problem has occurred when operating the ··º µÀ in the product. ¼efer to ¹ction 4.
¹ problem has occurred with the operation of the lamp. ¼efer to ¹ction 5.
The lifetime of the lamp has expired. ¼efer to ¹ction 6.
The memory in the product is not operating normally. Àontact a
service center
.
The power for the product is not operating normally. Àontact a
service center
.
¹ problem has occurred when operating the color wheel in the product. ¼efer to ¹ction
4.
Àlearing µndicator ºroblems
Àlassification
¿tate
Measures
¹ction 1
¶hen the cooling fan
system is not in normal
operating condition.
µf the symptom remains even after disconnecting and then
reconnecting the power cord and turning the projector on again,
contact your product provider or our
service center
.
¹ction 2
¶hen the lamp cover
protecting the lamp unit is
not properly closed or the
sensor system is not in
normal operating
condition.
Àheck whether the screws at the bottom side of the projector are
fastened correctly. µf they are abnormally fastened, contact your
product distributor or
service center
.