Samsung WF350ANW/XAA (English) - Page 16

setting up your new washing machine - lock

Get Samsung WF350ANW/XAA PDF manuals and user guides View all Samsung WF350ANW/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

setting up your washer 3. Check the inlet hose to ensure a washer is inside each fill hose. Cold Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and install each fill hose to the water valve. Make sure the hose with the Hot printed line is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an "nF" (no fill) error can occur. 4. Turn on the HOT and COLD water supply and check all connections at the water valve and the faucet for leaks. Cold printed Hot Hot printed 5. Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle. 6. Slide your washer into position. 7. Level your washer by turning the leveling legs in or out as necessary by hand or by using the wrench included with your washer. When your washer is level, tighten the locking nuts using the wrench or (-) flathead screwdriver. Your washer must be leveled on all four sides. A carpenter's level should be used on all four corners of your washer. It's the best to recheck after the first dozen washes. Locking Nut Avoid damage to the legs. Do not move the washer unless the locking-nuts are fastened to the bottom of the washer. Levelling Leg 16_ setting up your new washing machine WF350AN-02833A_EN.indd 16 2010-02-11 ¿ÀÀü 11:42:14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
16_
setting up your new washing machine
3.
Check the inlet hose to ensure a washer is inside each fill hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer per
hose and install each fill hose to the water valve. Make sure the
hose with the Hot printed line is attached to the HOT faucet.
Tighten by hand until snug, then two-thirds of a turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill) error
can occur.
4.
Turn on the HOT and COLD water supply and check all
connections at the water valve and the faucet for leaks.
5.
Plug the power cord into a 3-prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp
fuse or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
6.
Slide your washer into position.
7.
Level your washer by turning the leveling legs in or out as
necessary by hand or by using the wrench included with
your washer.
When your washer is level, tighten the locking nuts using
the wrench or (-) flathead screwdriver.
Your washer must be leveled on all four sides. A
carpenter’s level should be used on all four corners of
your washer. It’s the best to recheck after the first dozen
washes.
Avoid damage to the legs. Do not move
the washer unless the locking-nuts are
fastened to the bottom of the washer.
setting up your washer
Cold
Hot
Cold printed
Hot printed
Levelling
Leg
Locking
Nut
WF350AN-02833A_EN.indd
16
2010-02-11
¿ÀÀü 11:42:14