Samsung WF448AAW User Manual (ENGLISH) - Page 11

Step 2, Step 3, Step 4 - + drain

Get Samsung WF448AAW - 4.5 cu. ft. Steam Front Load Washer PDF manuals and user guides
UPC - 036725532922
View all Samsung WF448AAW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

01 Installing your washer STEP 2 Removing the Shipping Bolts Before using your Washer, you must remove the four shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Fill the holes with the supplied Bolt Hole Covers (See page 7). 4. Keep the shipping bolts and spacers for future use. STEP 3 Selecting a Location Before you install your washer, make sure the location: • Has a hard, level surface • Is away from direct sunlight • Has adequate ventilation • Will not freeze (below 32°F or 0°C) • Is away from heat sources such as oil or gas • Has enough slack for the power cord. • Doesn't have any carpeting that will obstruct ventilation openings. STEP 4 Installing your Washer 1. Place the drain hose in the drain facility. Be sure an airtight connection is NOT made between the drain hose and the standpipe. The standpipe must be at least 18 in or 46 cm high. Caution must always be exercised to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive lengths. For situations where the drain hose 96" Max 18" Min cannot be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. Laundry tub Stand pipe Hose retainer Tie strap 96" Max 18" Min 2. Insert new rubber washer (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings. WF448AAW-02535A-02_EN.indd 11 Installing your washer _11 2008-05-06 ¿ÀÈÄ 2:23:14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Installing your washer
_11
STEP 2
Removing the Shipping Bolts
Before using your Washer, you must remove the four shipping
bolts from the back of the unit.
1.
Loosen all the bolts with the supplied wrench.
2.
Slide the bolt and spacer up and remove the bolt with the
spacer through the hole in the rear wall of your washer.
Repeat for each bolt.
3.
Fill the holes with the supplied Bolt Hole Covers (See page 7).
4.
Keep the shipping bolts and spacers for future use.
STEP 3
Selecting a Location
Before you install your washer, make sure the location:
•
Has a hard, level surface
•
Is away from direct sunlight
•
Has adequate ventilation
•
Will not freeze (below 32°F or 0°C)
•
Is away from heat sources such as oil or gas
•
Has enough slack for the power cord.
•
Doesn’t have any carpeting that will obstruct ventilation openings.
STEP 4
Installing your Washer
1.
Place the drain hose in the drain facility. Be
sure an airtight connection is NOT made
between the drain hose and the standpipe.
The standpipe must be at least 18 in or 46
cm high.
Caution must always be exercised to
avoid collapsing or damaging the drain
hose. For best results, the drain hose
should not be restricted in any way – by
elbows, couplings, or excessive lengths.
For situations where the drain hose
cannot be conveniently elevated to at
least 18 in or 46 cm, the drain hose must
be supported.
2.
Insert new rubber washer (supplied) into each end of the
inlet hoses. Firmly seat the washers in the couplings.
01 Installing your washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub
Stand pipe
WF448AAW-02535A-02_EN.indd
11
2008-05-06
¿ÀÈÄ 2:23:14