Sanyo CE42LH2WP Owner's Manual - Page 11

11

INSTALLATION MODE

Installation Mode

Installation Mode

On program

Tuner Menu

Max Volume

Winter mode

RC inhibition

Child Lock

Address

Baud rate

Panel protection

AV Auto shut off

Network Standby

On Timer Function

LED light setting

DCR

Network initial

Temperature Error

IP Address

Subnet

Gateway

DNS

Off

Off

63

Off

Off

Off

0

19200

Off

Off

On

Off

Off

Off

>>>

0

000000000000

000000000000

000000000000

000000000000

G2.02 0000

Select

Ad

j

ust

MENU

Exit

This LCD monitor allows you to set up the following:

SETTING PROCEDURE

1.

Press and hold the

GREEN button

on the remote control for 5

seconds. (Installation Mode will appear)

2.

Use the

or

button

to highlight each option, use the

or

button

to adjust each option. Press the

MENU button

to exit

the mode.

On Program

Select ON program using the

or

button

, select the start up

position using the

or

buttons

.

Max Volume

Select Max volume using the

or

button

, use the

or

buttons

to set the maximum volume required.

Winter mode

This Function can be activated when the LCD monitor is used dur-

maintain picture performance.

Using the

or

button

select winter mode, once highlighted you

can select ON or OFF by pressing the

or

button

.

IMPORTANT: The AC cord should not be disconnected during the

operation of Winter mode function.

When in winter mode, power consumption is higher than normal

standby consumption. This is entirely due to the operation of heating

circuitry. We strongly recommend to turn off Winter mode when the

RC inhibition

You can prevent unwanted remote control operation by selecting RC

Inhibition.

Select using the

or

button

. Press the

or

button

to

select On or Off.

To re-instate RC operation press and hold the green button on the

remote control and select RC inhibition OFF.

Child Lock

You can prevent unwanted operation of the LCD monitor via the

buttons on the rear of the monitor.

Select using the

or

button

. Press the

button

to select

Address

Set the address for the LCD monitor (0 ~ 999).

Setting the monitor address in RS232 mode

that monitor individually and will not effect to other monitors con-

nected to a controlling PC Address format command.

The addressing format command is used for operating multiple

monitor sets from a single PC via the RS232C command line.

Baud rate

Select Baud rate using the

or

button

. To set transmission

speed RS232 or LD-NET communication for 19200 or 9600 Baud rate

by pressing the

or

button

.

Panel protection

long time, select “Panel Protect” using the

or

button

, once

highlighted you can select ON or OFF by pressing the

or

button

.

AV Auto shut off

With no picture input signal to AV1, RGB, AV2(YPbPr), AV3, DVI,

the

or

button

, once highlighted you can select On or Off by

pressing the

or

button

.

Network Standby

in Installation mode, both RS232C and LD-NET do not functional. To

On Timer Function

You can save power consumption selecting “Off” at On Timer function

in Installation mode. On Timer in Time menu does not functional. To

LED Light setting

Select LED Light setting using the

or

button

, once highlight-

ed you can select On or Off by pressing the

or

button

.

DCR

The picture contrast improved while DCR is ON. Select DCR using

the

or

button

, once highlighted you can select On or Off by

pressing the

or

button

.

Network Initial

This function automatically installs the IP Address, Subnet, Gateway

and DNS information.

Temperature Error

The recorded number of abnormal temperature is occurred is indi-

cated here.

IP Address/Subnet/Gateway/DNS

These 4 items display the LD-Net information. If LD-NET is NOT con-

nected, all the items would be displayed as “000000000000”.

Disconnecting the mains supply before exiting Installation Mode will

cancel the following features On program, RC inhibition, Address

and Baud Rate.

GB

GB

Sanyo CE42LH2WP Owner's Manual - Page 11

Installation Mode

Page 11 highlights