Sanyo CE52LH1R Owner's Manual - Page 10

10

This LCD monitor allows you to set up the following:

SETTING

PROCEDURE

1.

Press and hold the

GREEN button

on the remote control for 5

seconds. (Installation Mode will appear)

2.

Use the

5

or

6

button

to highlight

each option

, use the

1

or

2

button to adjust each option.

Press the

MENU button

to exit

the mode.

■

On Program

Select ON program using the

5

or

6

button, select the start up

position using the

1

or

2

buttons.

(Off/ AV1/ RGB/ AV2/ AV3/ PC/ DVI or Network)

■

Max Volume

Select Max volume using the

5

or

6

button, use the

1

or

2

buttons to set the maximum volume required.

■

Winter mode

This Function can be activated when the LCD monitor is used during

cold temperature conditions, approximately 38˚F/ 4˚C or below to

maintain picture performance.

Using

the

5

or

6

button

select winter mode, once highlighted

you can select ON or OFF by pressing the

1

or

2

button

.

IMPORTANT: The AC cord should not be disconnected during the

operation of Winter mode function.

When in winter mode, power consumption is higher than normal

standby consumption. This is entirely due to the operation of heating

circuitry. We strongly recommend to turn off Winter mode when the

ambient temperature is above 38˚F/ 4˚C.

■

RC inhibition

You can prevent unwanted remote control operation by selecting RC

Inhibition.

Select using the

5

or

6

button.

Press the

1

or

2

button

to select On or Off.

To re-instate RC operation press and hold the green button on the

remote control and select RC inhibition OFF.

■

Child Lock

You can prevent unwanted operation of the LCD monitor via the

buttons on the rear of the monitor.

Select using the

5

or

6

button.

Press the

1

button

to select

On or OFF.

The ‘Child Lock’ OSD will appear if buttons are pressed

when child lock is On.

✐

Standby operates normally when childlock is set “On”.

■

Address

Set the address for the LCD monitor (0 - 999).

■

Baud rate

Select Baud rate using the

5

or

6

button.

To set transmission

speed RS232 or LD-NET communication for 19200 or 9600 Baud

rate by pressing the

1

or

2

button

.

■

Panel Protect

Select Panel Protect using the

5

or

6

button

, once highlighted

you can select ON or OFF by pressing the

1

or

2

button

.

■

AV Auto shut off

Select AV Auto Shut Off using the

5

or

6

button

, once high-

lighted you can select On or Off by pressing the

1

or

2

button

.

■

LED Light setting

Select LED Light setting using the

5

or

6

button

, once high-

lighted you can select On or Off by pressing the

1

or

2

button

.

■

DCR

Select DCR using the

5

or

6

button

, once highlighted you can

select On or Off by pressing the

1

or

2

button

.

■

Network Initial

This function automatically installs the IP Address, Subnet, Gateway

and DNS information.

■

Temperature Error

This function can record times for abnormal temperture.

■

IP Address / Subnet / Gateway / DNS

These 4 items display the LD-Net information. If LD-NET is

NOT

connected, all the items would be displayed as “000000000000”.

✐

Disconnecting the mains supply before exiting Installation Mode

will cancel the following features On program, RC inhibition, Address

and Baud Rate.

INST

INST

ALLA

ALLA

TION MODE

TION MODE

GB

GB

I

nstallation Mode

Temperature Error

VER -.--

Network

I

nitial

>>>

Installation Mode

Sanyo CE52LH1R Owner's Manual - Page 10

Tion Mode

Page 10 highlights