Sanyo CE52LH1R Owner's Manual - Page 8

GB MENU OPERATION GB Picture menu I Advanced settings Use the 5 or 6 button to select Advanced settings and press the 1 or 2 button to enter the sub menu as follows. DCDi(Directional Correlational Deinterlacing) is used to process moving angled edge in deinterlacing to get the smoothest and most natural image. Press the 1 or 2 button on the remote control to select On or Off. ACC/ACM(ACC: Adaptive Contrast and Color; ACM-II: Active Color Management-II) is used to select adaptive Brightness, Contrast and tone control. Press the 1 or 2 button on the remote control to select suitable mode either Vivid, Cinema, Sport or Off. CCS(Cross Color Separation) is used to remove residual chroma information from luminance signal which is the result of imperfect decoding of composite video. Press the 1 or 2 button on the remote control to select either Auto, Standard or Off. DNR(Digital Noise Reduction) is available for noise reduction. Press the 1 or 2 button on the remote control to select either Auto, Low, Mid, High or Off. MPEG NR(MPEG Noise Reduction): Removes unwanted ringing and block noise from images that have undergone MPEG or JPEG compression and decompression. Press the 1 or 2 button on the remote control to select On or Off. Film Mode(Inverse 3:2 pulldown): Film vs.Video-Detect film. Performed on material which underwent technologic conversion to video. Press the 1 or 2 button on the remote control to select On or Off. Sound menu Press the MENU button and select Sound using the 5 or 6 buttons, press the 1 or 2 button to enter. I Current Weekday Use to set current weekday using the 1 or 2 button. I Current Time Use to set the current time using the Numeric buttons. i Other items in Time Menu should not be selected until Current Time has been set. I Schedule Use to set up to 20 separate time schedules, select 1 - 20 using the 1 or 2 button. I Weekday Use to set any weekday from Sunday through to Saturday or Everyday using the 1 or 2 button. I Time Use to set any time using the Numeric buttons. I Action Use to set "Power On" or "Power Off" using the 1 or 2 button. I On Program Use to select AV1, RGB, AV2, AV3, PC, DVI or Network using the 1 or 2 button. I Active Use to select ON or OFF using the 1 or 2 button. When set "OFF" the above items "Schedule", "Weekday", "Time", "Action" or "ON Program" will be inactive. Use NUMERIC buttons [0-9] to set On Time. (Action "Power On" 00:00~23:59) i Once On Time has been set, when the set time is reached, the monitor will leave the stand-by status and enter to the source automatically. i After On Time has been set, you can go on watching other programs. When the set time is reached, the monitor will automatically switch to the preset program. i On Program can only be selected whenAction (Power On) has been set. i Action (Power Off) can be set to turn the monitor into standby at a selected time Once On Program has been set, when the set time is reached, the monitor will enter to the preset source automatically. Use the 1 or 2 button to select On program, AV1, RGB, AV2, AV3, PC, DVI or Network. Setup menu Press the MENU button and select Setup using the 5 or 6 buttons, press the 1 or 2 button to enter. Press the BACK button to return to the previous menu. Press the MENU button to exit Select and adjust to obtain the best sound settings for your environment using the 5 or 6 button to select Treble, Bass or Balance and the 1 or 2 button to adjust levels. Bass Expander can also be selected using the 5 or 6 button and pressing the 1 or 2 button to select On or Off. These settings automatically store when you exit the menu. Press the BACK button to return to the previous menu. Press the MENU button to exit menu operation. Time menu Press the MENU button and select Time using the 5 or 6 buttons, press the 1 or 2 button to enter. Press the BACK button to return to the previous menu. Press the MENU button to exit menu operation. Current Weekday Current Time Schedule Weekday Time Action On Program Active Friday 12:17 1 Friday 12:03 Power Off AV3 7V 8 :M[WT]\QWV PC Power Save @/) On I Menu Setup Whenever Setup menu is accessed initially, Menu Setup will be the default selection. Press the 1 or 2 button to enter the sub menu. Language is used to select the preferred language. Use the 1 or 2 button to select English, French, German, Italian, Spanish or Dutch. H-Position changes the OSD position horizontally by using the 1 or 2 button. V-Position changes the OSD position vertically by using the 1 or 2 button. Duration is used to set the display time of the MENU by using the 1 or 2 button.(5~120 seconds) Transparence is used to adjust transparence of menu. Use the 1 or 2 button to adjust levels.