Sanyo ECD-T1580DV Owners Manual - Page 6

Installation - harness

Get Sanyo ECD-T1580DV PDF manuals and user guides View all Sanyo ECD-T1580DV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

INSTALLATION Notes: DIN FRONT-MOUNT (Method A) Choose the mounting location where the unit will not interfere with the normal driving function of the driver . Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is an emergency stop. If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance. 30 Installation Opening This unit can be installed in any dashboard having an opening as shown below: 53 mm 182 mm Installing the unit Be sure you test all connections first, and then follow these steps to install the unit. 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. 2. Disconnect the wire harness and the antenna. 3. Lift the top of the outer trim ring then pull it out to remove it. 4. The two supplied keys release tabs inside the unit's sleeve so you can remove it. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit. Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air , from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONT/REAR-MOUNT Sleeve L Key Outer Trim Ring R Key byinserting the sleeve This unit can be properly installed either from "Front" (conventional DIN Frontmount) or "Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. 5. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
6
INSTALLATION
Notes:
Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver .
Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
Use only the parts included with the
unit to ensure proper installation.
The use of
unauthorized parts can
cause malfunctions.
Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
Install the unit where it does not get in
the driver's way and cannot injure the
passenger if there is
an emergency
stop.
If installation angle exceeds 30
from
horizontal, the unit might not give its
optimum performance.
Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from "Front" (conventional DIN Front-
mount) or "Rear" (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard
having an opening as shown below:
Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.
1.
Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.
2.
Disconnect the wire harness and the
antenna.
3.
Lift the top of the outer trim ring then
pull it out to remove it.
4.
The two supplied keys release tabs
inside the unit's sleeve so you can
remove it. Insert the
keys as far as they
will go (with the notches facing up) into
the appropriate slots
at the middle left
and right sides of the unit. Then slide
the sleeve off the back of the unit.
5.
Mount the sleeve by inserting the sleeve
by
inserting the sleeve
into the opening of the dashboard
and
bend open the tabs located around the
sleeve with a screwdriver. Not all
tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.
30
182 mm
53 mm
Outer Trim Ring
L Key
Sleeve
R Key