Sanyo FW40D48F Owners Manual - Page 5

1 Notice SANYO is a registered trademark of SANYO Electric Co., Ltd. and is used by Funai Electric Co., Ltd. and Funai Corporation, Inc. under license from SANYO Electric Co., Ltd. Any liability related to SANYO products, including design and quality, is the sole responsibility of Funai Electric Co., Ltd. and Funai Corporation, Inc. Please contact Funai Corporation, Inc. for any questions or claims related to SANYO products: www.sanyo-av.com Funai reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this Owner's manual is believed adequate for the intended use of the system. If the product or its individual modules or procedures are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained. Funai warrants that the material itself does not infringe any United States patents. No further warranty is expressed or implied. Funai cannot be held responsible neither for any errors in the content of this document nor for any problems as a result of the content in this document. Errors reported to Funai will be adapted and published on the Funai support website as soon as possible. Pixel characteristics This LCD product has a high number of color pixels. Although it has effective pixels of 99.999% or more, black dots or bright points of light (red, green or blue) may appear constantly on the screen. This is a structural property of the display (within common industry standards) and is not a malfunction. Warranty No components are user serviceable. Do not open or remove covers to the inside of the product. Repairs may only be done by service centers and official repair shops. Failure to do so shall void any warranty, stated or implied. Any operation expressly prohibited in this Owner's manual, any adjustments or assembly procedures not recommended or authorized in this Owner's manual shall void the warranty. Federal communications commission notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and the receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio or television technician for help. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Declaration of conformity Trade name : SANYO Responsible party : FUNAI CORPORATION, Inc. Model : FW40D48F Address : 19900 Van Ness Avenue, Torrance, CA 90501 U.S.A. Telephone number : 1 866 212 0436 5 .English Modifications This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference. Any modifications to the apparatus must be approved by Funai. The user could lose the authority to operate this apparatus if an unauthorized change or modification is made. Cables Connections to this device must be made with shielded cables with metallic RFI / EMI connector hoods to maintain compliance with FCC Rules and regulations. Canadian notice CAN ICES-3 (B) / NMB-3 (B) Analog and digital television receiving apparatus, Canada BETS-7 / NTMR-7. Positioning the TV ● Large screen TVs are heavy. 2 people are required to carry and handle a large screen TV. ● Make sure to hold the upper and bottom frames of the unit firmly as illustrated. ● Install the unit in a horizontal and stable position. ● Do not install the unit in direct sunlight or in a place subject to dust or strong vibration. ● Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction. ● When installing this unit in a temperate environment, avoid a place with rapid temperature changes. - Operating temperature: 41°F (5°C) to 104°F (40°C) ● This unit should not be used in a tropical environment as it has not been evaluated under such conditions. ● No objects should be placed directly on or under this unit, especially lighted candles or other flaming objects. ● Depending on your external devices, noise or disturbance of the picture and/or sound may be generated if the unit is placed too close to them. In this case, please ensure enough space between the external devices and the unit. ● Do not insert the AC power cord into the power socket outlet before all the connections are made. ● Ensure that you always have easy access to the AC power cord and outlet to disconnect the TV from the AC outlet. ● Before you move the TV, disconnect attached cables to prevent damage to connectors, especially the TV tuner. ● Be sure to unplug the AC power plug from the AC outlet before moving or carrying the unit. ● When moving the TV and then setting it down, please be careful not to pinch the AC power cord under the unit. ● Do not place this unit in an area where it may be exposed to water, oil or grease such as: near a bathtub, basin, kitchen sink, washing tub, swimming pool, kitchen exhaust fan, etc., or in a damp basement.