Sanyo FWDP175F Owners Manual - Page 22

INFORMATION Troubleshooting Guide If the Unit does not perform properly when operated as instructed in this Owner's Manual, refer to the following. Problem No Power. No Sound or Picture. Distorted Picture. Completely Distorted Picture or Black / White Picture with DVD. No Sound or Distorted Sound. No DTS Audio is Output. Bitstream is not output in Dolby Digital audio. Picture Freezes Momentarily during Playback. Disc Cannot be Played back. No Return to Start-up Screen when Disc is Removed. The Unit does not Respond to the Remote Control. Buttons Do Not Work or the Unit Stops Responding. The Unit Does Not Respond to some Operating Commands during Playback. The Unit Cannot Read CD / DVD. Angle Does Not Switch. The Password for Rating Level has been Forgotten. Corrective action --Check if the AC Power cord is properly connected. --Unplug from the AC outlet, and wait for 5-10 seconds and then Plug it in again. --Check if the TV is switched On. --Check the Video Connection. --Check the Audio / Video Cable connections to the TV. (Refer to page 8.) --Check whether the connected TV or other device supports HDCP. (This unit will not output a video signal unless the other device supports HDCP.) --Press and hold [ BF (PLAY / PAUSE) ] on the front panel for 5 seconds to change back to default output. --Sometimes a small amount of Picture Distortion may appear. This is Not a Malfunction. --Connect the unit directly to the TV. --Connect this unit directly to the TV. --Make sure the Disc is Compatible with the unit. --Adjust the Volume. --Check that the Speakers are Connected correctly. --This unit does Not support DTS Audio. This is Not a Malfunction. --You need to set this unit to "Bitstream" in "Audio Out" Menu and also need to connect to the TV or Amplifier that supports DTS, then the Audio will be output as DTS. It is only available when connected via an HDMI cable. -- When Voice Guide is set to "On", "Audio Out" is fixed to "PCM" and it is unconfigurable. In order to change "Audio Out" to "Bitstream", press [SETUP] on the remote control, select "SYSTEM"  "Voice Guide"  "Off", then set "Audio Out" to "Bitstream". -- Make sure that "Voice Guide" is set to "Off". "Audio Out" is fixed to "PCM" when "Voice Guide" is set to "On". In order to set "Audio Out" to "Bitstream", set "Voice Guide" to "Off". --Check the Disc for Fingerprints / Dirty and Clean with a Soft cloth wiping from center to edge. -- When Voice Guide is set to "On" and playback functions (such as Fast-forward, etc) are used, DVD playback will be interrupted while a Voice Guide message is being output. In order to disable Voice Guide, press [SETUP] on the remote control, then select "SYSTEM"  "Voice Guide"  "Off". --Clean the Disc. --Ensure the Disc is inserted in Correct position. --Insert a Correct Type disc that Plays back on this unit. --Check if the Disc is defective by trying another disc. --Check if the Parental settings exceeds the levels you set in the "Movie Rating" setting. (for DVD only) --Handle a Disc with special care so that it does not have Fingerprints, Scratches, or Dust on its surface. --Turn Off the unit once and then restart. --Aim the Remote Control Directly at the Sensor on the Front Panel. --Reduce the Distance to the unit. --Re-insert the Batteries with their Polarities (+ / - signs) as indicated. --Replace the Batteries in the Remote Control. --Press and Hold any buttons on the Remote Control toward a Digital Camera. The Remote Control is working if you confirm a pulsating infrared light through the Digital Camera. --Please attempt to Reset the unit by Unplugging the AC Power cord from the Wall outlet and then Plug it in again after 5-10 seconds. --Operations may Not be permitted by the Disc. Refer to the instructions for the disc. --Use a commonly available Cleaning CD / DVD disc to Clean the Lens before sending the Unit for Repair. --The Angle cannot be switched for a DVD which does not contain Multiple Angles. In some cases Multiple Angles are only recorded for specific Scenes. --Enter the Default Password "4737", then your Forgotten Password will be Cleared. Then the Rating Level plus Password will have to be set again. • Some Functions are not available in Specific modes, but this is Not a Malfunction. Read the description in this Owner's Manual for more details on Correct Operation's. • Not all Functions are available for all Commercial discs. Specifications Output Signal Format: NTSC color Power Source: 120 V AC + / - 10%, 60 Hz + / - 0.5% Power Consumption: 7 W (standby : 0.9 W) EN Operating Temperature: 41°F (5 °C) to 104 °F (40 °C) Dimensions: W : 9.9 inches (250 mm) H : 2.0 inches (50.2 mm) D : 7.4 inches (187.7 mm) - 22 - Weight: Approx 1.95 lbs. (0.88 kg) • Designs and Specifications are subject to change without notice. • If there is a Discrepancy between Languages, the default Language will be English.