Sanyo PLC-XW56 Owners Manual - Page 54

Lamp Replacement - model

Get Sanyo PLC-XW56 - XGA LCD Projector PDF manuals and user guides
UPC - 086483069246
View all Sanyo PLC-XW56 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Maintenance and Cleaning Lamp Replacement When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow, replace the lamp with a new one promptly. WARNING: TURN OFF THE UV LAMP BEFORE OPENING THE LAMP COVER TOP CONTROL This indicator is yellow when the life of the projection lamp draws to an end. CAUTION CAUTION Allow a projector to cool, for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot. For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury. Follow these steps to replace the lamp. 1 Turn off the projector and disconnect the AC power cord. Allow the projector to cool for at least 45 minutes. Lamp Cover 2 Loosen the screw with a screwdriver, and remove the lamp cover. 3 Loosen the 3 screws of the lamp with a screwdriver and lift the lamp out of the projector by using the built in handles. 4 Replace the lamp with a new one and secure it with the 3 screws. Make sure that the lamp is set properly. Replace the lamp cover and tighten the screw. Lamp Screw 5 Connect the AC power cord to the projector and turn on the projector. Screw 6 Reset the lamp replacement counter. See "Lamp Replacement Counter" on the next page . Screw Screw Handles ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector: PLC-XW56 ● Replacement Lamp Type No.: POA-LMP107 (Service Parts No. 610 330 4564) 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Maintenance and Cleaning
54
When the life of the projection lamp of this projector
draws to an end, the LAMP REPLACE indicator emits
a yellow light.
If this indicator lights yellow, replace the
lamp with a new one promptly.
Lamp Replacement
WARNING:
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER
TOP CONTROL
For continued safety, replace with a lamp of
the same type.
Do not drop a lamp or touch
a glass bulb!
The glass can shatter and
may cause injury.
Allow a projector to cool, for at least 45
minutes before you open the Lamp cover.
The inside of the projector can become very
hot.
CAUTION
CAUTION
Follow these steps to replace the lamp.
Turn off the projector and disconnect the AC power
cord.
Allow the projector to cool for at least 45
minutes.
Loosen the 3 screws of the lamp with a screwdriver
and lift the lamp out of the projector by using the
built in handles.
Replace the lamp with a new one and secure it
with the 3 screws.
Make sure that the lamp is set
properly.
Replace the lamp cover and tighten the
screw.
Loosen the screw with a screwdriver, and remove
the lamp cover.
Connect the AC power cord to the projector and
turn on the projector.
Reset the lamp replacement counter°
See "Lamp Replacement Counter" on the next
page .
1
2
3
4
5
6
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.
When ordering a projection lamp, give the
following information to the dealer.
●
Model No. of your projector:
PLC-XW56
●
Replacement Lamp Type No.:
POA-LMP107
(Service Parts No. 610 330 4564)
Lamp
Screw
Handles
Screw
Lamp Cover
Screw
This indicator is
yellow when the life
of the projection lamp
draws to an end.
Screw