Sanyo WXE45 User Manual - Page 53

How to install the battery, ● Do not disassemble, or apply pressure to transform the battery.

Get Sanyo WXE45 - PLC WXGA LCD Projector 720p PDF manuals and user guides
UPC - 086483072819
View all Sanyo WXE45 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Antitheft Alarm Function How to install the battery To use the Antitheft alarm function, you need to install a battery. (Use CR2 3V lithium battery.) Unplug the AC power cord from the wall outlet before installing the battery. Remove the screw and open the battery cover on the bottom of the projector. When the battery is installed properly, the ALARM indicator blinks for about 10 seconds. After placing the battery, put the cover back and secure it with the screw. When the life of the battery draws to an end, the ALARM indicator flashes and warning sound is made at some intervals. Replace the battery by following the procedures above. Note: • Even after changing the battery, the PIN code you have changed and settings you have made are effective. • When changing the battery, set the Antitheft alarm function off. Otherwise the alarm starts ringing when you try to open the battery cover. • Remove the battery if you carry your projector frequently and use the carrying case. If you do not remove the battery, the alarm may be triggered when the Alarm buttons are accidentally pressed inside the carrying case. Screw Loosen the screw and open the battery cover. Install the battery then replace the battery cover and secure it with the screw. To insure safe operation, please observe the following precautions: ● Do not keep the battery mixing with wire or metal products to avoid causing a short. ● Keep the battery away from babies and children to prevent them from swallowing it. ● Do not charge the battery. ● Do not disassemble, or apply pressure to transform the battery. ● Avoid contact with water or liquid. ● Do not expose to moisture or heat. ● If the battery has leaked, carefully wipe the battery compartment clean and install new battery. ● Do not replace the battery with an incorrect type or in an incorrect direction. ● Dispose of used battery after insulating the battery with putting insulating tape on either or both sides on the top/bottom of the battery. ● Dispose of used battery according to the local regulations. ● Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
5²
How to install the battery
To use the Antitheft alarm function, you need to install a
battery. (Use CR2 3V lithium battery.)
Unplug the AC power cord from the wall outlet before
installing the battery. Remove the screw and open the
battery cover on the bottom of the projector.
When the battery is installed properly, the ALARM indicator
blinks for about 10 seconds.
After placing the battery, put the cover back and secure it
with the screw.
When the life of the battery draws to an end, the ALARM
indicator flashes and warning sound is made at some
intervals.
Replace the battery by following the procedures above.
Note:
• Even after changing the battery, the PIN code you have
changed and settings you have made are effective.
• When changing the battery, set the Antitheft alarm
function off.
Otherwise the alarm starts ringing when you
try to open the battery cover.
• Remove the battery if you carry your projector frequently
and use the carrying case. If you do not remove the
battery, the alarm
may be triggered when the Alarm
buttons are accidentally pressed inside the carrying
case.
Loosen the screw and
open the battery cover.
Install the battery then replace the
battery cover and secure it with the
screw.
Screw
To insure safe operation, please observe the following precautions:
● Do not keep the battery mixing with wire or metal products to avoid causing a short.
● Keep the battery away from babies and children to prevent them from swallowing it.
● Do not charge the battery.
● Do not disassemble, or apply pressure to transform the battery.
● Avoid contact with water or liquid.
● Do not expose to moisture or heat.
● If the battery has leaked, carefully wipe the battery compartment clean and install new battery.
● Do not replace the battery with an incorrect type or in an incorrect direction.
● Dispose of used battery after insulating the battery with putting insulating tape on either or both
sides on the top/bottom of the battery.
● Dispose of used battery according to the local regulations.
● Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type
recommended by the manufacturer.
Antitheft Alarm Function