Sanyo WXU700 Instruction Manual, PLC-WXU700 Network Set Up Macintosh - Page 99

Command list table

Get Sanyo WXU700 - WXGA LCD Projector PDF manuals and user guides
UPC - 086483074219
View all Sanyo WXU700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Use of telnet 5. Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projector, and press "Enter" key. Confirm the projector is turning on. * Enter with ASCII 64-byte capital characters and one-byte characters. To disconnect the communication, press "Control" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard. > close [return] The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another commands. Command list table Command Function C00 Power on C02 Power off C09 Volume up C0A Volume down C0B Audio Mute on C0C Audio Mute off C1C Menu display on C1D menu display off *1 Further instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" (☞p.32, 42). If the authentication of the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please try again for the connection. *3 If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection. 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
¸¸
5. Type the commands, refer to below table, to control the projector and then press "Enter" key for
termination. For example, type "C00" which is a command to turn on the projector, and press "Enter"
key. Confirm the projector is turning on.
*
Enter with ASCII 64-byte capital characters and one-byte characters.
To disconnect the communication, press "Control" key and "]" key at the same time, type "close" and
then press "Enter" key on the Keyboard.
> close [return]
The table below shows the typical command lists for controlling this projector and please consult your
local dealer for further information of another commands.
*1 Further instructions about the telnet application, please see the on-line guide on your computer.
*2 The password is a Network PIN code decided item "Network PIN code setting" (
☞
p.32, 42). If the authentication of
the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please
try again for the connection.
*3 If the password or any command is not entered for more than 30 seconds, the communication will be disconnected
automatically. Please try again for the connection.
Command
Function
C00
Power on
C02
Power off
C09
Volume up
C0A
Volume down
C0B
Audio Mute on
C0C
Audio Mute off
C1C
Menu display on
C1D
menu display off
Command list table
Use of telnet