Home » Seagate Manuals » Hard Drives » Seagate Pipeline HD » Manual Viewer

Seagate Pipeline HD Pipeline HD Series SATA Product Manual - Page 26

Drive mounting, Pipeline HD SATA Product Manual, Rev. D, Configuring and Mounting the Drive

View all Seagate Pipeline HD manuals

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Configuring and Mounting the Drive Figure 3 Attaching SATA cabling Signal connector Power connector Signal cable www.seagate.com Power cable Each cable is keyed to ensure correct orientation. Pipeline HD drives support latching SATA connectors. 3.4 Drive mounting You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 in (0.76mm) around the entire perimeter of the drive for cooling. • Use only 6-32 UNC mounting screws. • The screws should be inserted no more than 0.150 in (3.81mm) into the bottom or side mounting holes. • Do not overtighten the mounting screws (maximum torque: 6 in per lb). 26 Pipeline HD SATA Product Manual, Rev. D

Section	Page
Pipeline HD®	1
1.0 Introduction	9
1.1 About the Serial ATA Interface	9
2.0 Drive Specifications	11
2.1 Specification summary tables	11
2.2 Formatted capacity	13
2.2.1 LBA mode	13
2.3 Default logical geometry	13
2.4 Recording and interface technology	13
2.5 Physical characteristics	14
2.6 Seek time	14
2.7 Start/stop times	14
2.8 Power specifications	14
2.8.1 Power consumption	15
2.8.2 Conducted noise	17
2.8.3 Voltage tolerance	17
2.8.4 Power-management modes	17
2.9 Environmental specifications	18
2.9.1 Drive case temperature	18
2.9.2 Temperature gradient	18
2.9.3 Humidity	18
2.9.4 Altitude	18
2.9.5 Shock	18
2.9.6 Vibration	19
2.10 Acoustics	20
2.10.1 Test for Prominent Discrete Tones (PDTs)	20
2.11 Electromagnetic immunity	20
2.12 Reliability - Annualized Failure Rate	21
2.13 Warranty	21
2.14 Agency certification	21
2.14.1 Safety certification	21
2.14.2 Electromagnetic compatibility	21
2.14.3 FCC verification	22
2.15 Environmental protection	22
2.15.1 European Union Restriction of Hazardous Substances (RoHS) Directive	22
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive	22
2.16 Corrosive environment	23
3.0 Configuring and Mounting the Drive	25
3.1 Handling and static-discharge precautions	25
3.2 Configuring the drive	25
3.3 Serial ATA cables and connectors	25
3.4 Drive mounting	26
4.0 Serial ATA Interface	29
4.1 Hot-Plug compatibility	29
4.2 Serial ATA device plug connector pin definitions	29
4.3 Supported ATA commands	30
4.3.1 Identify Device command	33
4.3.2 Set Features command	37
4.3.3 S.M.A.R.T. commands	38
A	39
B	39
C	39
D	39
E	39
F	39
G	39
H	39
I	39
K	39
L	40
M	40
N	40
O	40
P	40
R	40
S	40
T	41
U	41
V	41