Home » Seagate Manuals » Hard Drives » Seagate ST1000VX000 » Manual Viewer

Seagate ST1000VX000 SV35 Series PATA Product Manual - Page 44

S.M.A.R.T. commands, Note.

View all Seagate ST1000VX000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

4.1.4 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-7 Standard. SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses. Code in features register S.M.A.R.T. command D0H S.M.A.R.T. Read Data D1H Vendor-specific D2H S.M.A.R.T. Enable/Disable Attribute Autosave D3H S.M.A.R.T. Save Attribute Values D4H S.M.A.R.T. Execute Off-line Immediate (runs DST) D5H S.M.A.R.T. Read Log Sector D6H S.M.A.R.T. Write Log Sector D7H Vendor-specific D8H S.M.A.R.T. Enable Operations D9H S.M.A.R.T. Disable Operations DAH S.M.A.R.T. Return Status Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register. 38 SV35 Series Product Manual, Rev. B

Section	Page
1.0 Introduction 1	3
2.0 Drive specifications 3	3
2.1 Specification summaries 3	3
2.2 Formatted capacity 10	3
2.2.1 LBA mode 10	3
2.3 Default logical geometry 10	3
2.4 Recording and interface technology 11	3
2.5 Physical characteristics 12	3
2.6 Seek time 12	3
2.7 Start/stop times 12	3
2.8 Power specifications 13	3
2.8.1 Power consumption 13	3
2.8.2 Conducted noise 14	3
2.8.3 Voltage tolerance 14	3
2.8.4 Power-management modes 15	3
2.9 Environmental specifications 16	3
2.9.1 Ambient temperature 16	3
2.9.2 Temperature gradient 16	3
2.9.3 Humidity 16	3
2.9.4 Altitude 16	3
2.9.5 Shock 17	3
2.9.6 Vibration 17	3
2.10 Acoustics 18	3
2.11 Electromagnetic immunity 19	3
2.12 Reliability 19	3
2.13 Agency certification 20	3
2.13.1 Safety certification 20	3
2.13.2 Electromagnetic compatibility 20	3
2.13.3 FCC verification 20	3
2.14 Environmental protection 21	3
2.14.1 European Union Restriction of Hazardous Substances (RoHS) 21	3
2.15 Corrosive environment 22	3
3.0 Configuring and mounting the drive 23	3
3.1 Handling and static discharge precautions 23	3
3.2 Breather filter hole precautions 24	3
3.3 Jumper settings 25	3
3.3.1 Master/slave configuration 25	3
3.3.2 Cable-select option 25	3
3.3.3 Alternate capacity jumper 25	3
3.3.4 Ultra ATA/100 cable 26	3
3.4 Drive mounting 26	3
4.0 ATA interface 29	3
4.1 ATA interface signals and connector pins 29	3
4.1.1 Supported ATA commands 30	3
4.1.2 Identify Device command 33	3
4.1.3 Set Features command 37	3
4.1.4 S.M.A.R.T. commands 38	3
4.1.5 Streaming feature set support 39	3
5.0 Seagate Technology support services 51	3
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summaries	9
2.2 Formatted capacity	16
2.2.1 LBA mode	16
2.3 Default logical geometry	16
2.4 Recording and interface technology	17
2.5 Physical characteristics	18
2.6 Seek time	18
2.7 Start/stop times	18
2.8 Power specifications	19
2.8.1 Power consumption	19
2.8.1.1 Typical current profile	20
2.8.2 Conducted noise	20
2.8.3 Voltage tolerance	20
2.8.4 Power-management modes	21
2.9 Environmental specifications	22
2.9.1 Ambient temperature	22
2.9.2 Temperature gradient	22
2.9.3 Humidity	22
2.9.3.1 Relative humidity	22
2.9.3.2 Wet bulb temperature	22
2.9.4 Altitude	22
2.9.5 Shock	23
2.9.5.1 Operating shock	23
2.9.5.2 Nonoperating shock	23
2.9.6 Vibration	23
2.9.6.1 Operating vibration	23
2.9.6.2 Nonoperating vibration	23
2.10 Acoustics	24
2.11 Electromagnetic immunity	25
2.12 Reliability	25
2.13 Agency certification	26
2.13.1 Safety certification	26
2.13.2 Electromagnetic compatibility	26
2.13.3 FCC verification	26
2.14 Environmental protection	27
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	27
2.15 Corrosive environment	28
3.0 Configuring and mounting the drive	29
3.1 Handling and static discharge precautions	29
3.2 Breather filter hole precautions	30
3.3 Jumper settings	31
3.3.1 Master/slave configuration	31
3.3.2 Cable-select option	31
3.3.3 Alternate capacity jumper	31
3.3.4 Ultra ATA/100 cable	32
3.4 Drive mounting	32
4.0 ATA interface	35
4.1 ATA interface signals and connector pins	35
4.1.1 Supported ATA commands	36
4.1.2 Identify Device command	39
4.1.3 Set Features command	43
4.1.4 S.M.A.R.T. commands	44
4.1.5 Streaming feature set support	45
4.1.5.1 Identify Device command	45
4.1.5.2 Streaming commands	45
4.1.5.2.1 Configure Stream (51h)	47
4.1.5.2.2 Read Stream DMA (2Ah)	48
4.1.5.3 Write Stream DMA (3Ah)	52
4.1.5.3.1 Time-constrained operations	54
4.1.5.3.2 Non-cached streaming writes use model	55
4.1.5.3.3 Non-streaming writes	55
5.0 Seagate Technology support services	57
Numerics	59
A	59
B	59
C	59
D	59
E	59
F	59
G	60
H	60
I	60
J	60
K	60
L	60
M	60
N	60
O	60
P	60
R	60
S	61
T	61
U	61
V	61

Match case Limit results 1 per page

SV35 Series Product Manual, Rev. B

4.1.4

S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-

tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines

that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.

S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.

commands and implementation, see the

Draft

ATA-7 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4

) that elimi-

nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:

http://seatools.sea

gate.com

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that

supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the

drive uses.

Note.

If an appropriate code is not written to the Features Register, the command is aborted and 0

(abort) is written to the Error register.

Code in features

S.M.A.R.T. command

S.M.A.R.T. Read Data

Vendor-specific

S.M.A.R.T. Enable/Disable Attribute Autosave

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Execute Off-line Immediate (runs DST)

S.M.A.R.T. Read Log Sector

S.M.A.R.T. Write Log Sector

Vendor-specific

S.M.A.R.T. Enable Operations

S.M.A.R.T. Disable Operations

S.M.A.R.T. Return Status