Seagate ST160LT007 Momentus Thin SATA Product Manual
Seagate ST160LT007 Manual
View all Seagate ST160LT007 manuals
Add to My Manuals
Save this manual to your list of manuals |
Seagate ST160LT007 manual content summary:
- Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 1
Product Manual Momentus® Thin Series SATA ST92503010AS ST91603010AS 100586949 Rev. B March 2010 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 2
trademarks are the property of their respective owners. No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC. One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer's operating system - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 3
2.9.4 Voltage tolerance 8 2.9.5 Power-management modes 9 2.10 Environmental specifications Supported ATA commands 21 4.3.1 Identify Device command 24 4.3.2 Set Features command 28 4.3.3 S.M.A.R.T. commands 29 5.0 Seagate Technology support services 30 Momentus Thin Series SATA Product Manual - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 4
ii Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 5
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Typical +5V only startup and operation current profile 8 Serial ATA connectors 17 Attaching SATA cabling 17 Mounting dimensions-top, side and end view 18 Momentus Thin Series SATA Product Manual, Rev. B iii - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 6
- Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 7
™, which includes Drive Defense, Data Defense and Diagnostic Defense, offers the industry's most comprehensive protection for disk drives. • Support for S.M.A.R.T. drive monitoring and reporting. • Support for Read Multiple and Write Multiple commands. Momentus Thin Series SATA Product Manual, Rev - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 8
providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current manages two sets of shadow registers. This is not a typical Serial ATA environment. The Serial ATA host adapter and drive SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 9
, see the appropriate section of this manual. Table 1: Drive specifications Drive specification Formatted GB (512 bytes/sector)* transfer rate (Mb/s max) I/O data transfer rate (MB/s max) ATA data-transfer modes supported Height (max) Width (max) Length (max) Weight (max) Power-on to ready ( - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 10
) Vibration, nonoperating Drive acoustics, sound power Warranty Supports hard power on/off cycles To determine the warranty for a specific drive, use a web browser to access the following web page: support.seagate drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 11
equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and 100-103) for additional information about 48bit addressing support of drives with capacities over 137 GB. 2.3 Default logical geometry Series SATA Product Manual, Rev. B 5 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 12
seek times (ms) Track-to-track Average Full-stroke Average latency Read 1 14 30 (max) 5.56 Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted values - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 13
drive spindle reaches operating speed. • Seek mode During seek mode, the read/write actuator arm moves toward a specific position on the disk the drive up to speed, with servo mode, the drive accepts commands, but the drive is not 0.20W *During periods of drive idle, some offline activity may - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 14
Momentus Thin Series SATA drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives. 2.9.3 Conducted noise Input Voltage tolerance (including noise): 5V ± 10% 8 Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 15
to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disk access is necessary. Momentus Thin Series SATA Product Manual, Rev. B 9 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 16
temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C -304.8 m to 12,192 m (-1000 ft to 40,000+ ft) 10 Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 17
These drives comply with level that the drive can experience level that the drive can experience without level that the drive can experience without drive is mounted securely with the input vibration applied at the drive vibration levels that the drive may experience while meeting that the drive may - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 18
levels for steady state, idle, and active seek modes of operation. Table 5: Drive A-weighted Sound Power Levels (SWL, BA) Idle* 2.0 bels (typ) 2.2 is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 19
on/off cycles 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles To determine the warranty for a specific drive, use a web browser to access the following web page: support.seagate.com/customer/warranty_validation.jsp From this page, click on the "Verify Your Warranty - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 20
FCC verification These drives are intended device). As such, each drive is considered to be Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive manufacturer's instructions, may Television Interference Problems. This - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 21
by the China RoHS MCV Standard. "X RoHS MCV 2.16 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial near circuitry with sulfide-free alternatives. Momentus Thin Series SATA Product Manual, Rev. B 15 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 22
printed circuit board. • Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. 16 Momentus - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 23
because each drive is considered a master in a point-to-point relationships. If two drives are attached drive for proper operation. If the host system does not support SATA 3Gb/s operation, place a jumper on pins 1 and 2 to limit the drive , you can connect the drive as illustrated in Figure 3. - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 24
drive hard errors 10 mm probe: 1.02kgf or 5 mm probe: 0.92kgf 20 mm probe: 2kgf at any point of top cover 20 mm probe: 15kgf at top cover edges only Measurements shown in Figure 4 are in inches. Figure 4. Mounting dimensions-top, side and end view 18 Momentus Thin Series SATA Product Manual - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 25
input/output (PIO) modes 0-4; multiword DMA modes 0-2, and Ultra DMA modes 0-6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed Key and spacing separate signal and power segments Momentus Thin Series SATA Product Manual, Rev. B 19 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 26
used for pre-charge when installed in a blind-mate backplane configuration. 4. All used voltage pins (Vx) must be terminated. 20 Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 27
ATA commands The following table lists Serial ATA standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment 27h 20h 24h 21h 40h 42h 41h 70h EFh F9h Momentus Thin Series SATA Product Manual, Rev. B 21 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 28
33h Write Multiple C5h Write Multiple Extended 39h Write Sectors Write Sectors Extended 30h, 31h 34h Write Uncorrectable 45h ATA-standard power-management commands Check Power Mode E5h Idle E3h Idle Immediate E1h Sleep E6h Standby E2h 22 Momentus Thin Series SATA Product - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 29
Command name Standby Immediate ATA-standard security commands Security Set Password Security Unlock Security Erase Prepare Security Erase Unit Security Freeze Lock Security Disable Password Command code (in hex) E0h F1h F2h F3h F4h F5h F6h Momentus Thin Series SATA Product Manual, Rev. B 23 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 30
Firmware revision (8 ASCII character string, padded with blanks to end of string) Drive model number: (40 ASCII characters, padded with blanks to end of string) (Bits 7-0) Maximum sectors per interrupt on Read multiple and Write multiple (16) Reserved Standard Standby timer, IORDY supported - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 31
sets enable extension Ultra DMA support and current mode (see note following this table) Security erase time Enhanced security erase time Master password revision code Hardware reset value (see description following this table) Auto acoustic management setting Value xxxxH ST92503010AS = 0FFFFFFFh - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 32
) These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh. ATA-reserved Free Fall Protection support (bit 5) Free Fall Protection enable/disable (bit 5) ATA reserved Security status Seagate-reserved ATA-reserved Integrity word Value - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 33
supported. 1 Ultra DMA mode 1 is supported. 2 Ultra DMA mode 2 is supported. 3 Ultra DMA mode 3 is supported. 4 Ultra DMA mode 4 is supported. 5 Ultra DMA mode 5 is supported 6 Ultra DMA mode 6 is supported detected, CBLID below VIL Momentus Thin Series SATA Product Manual, Rev. B 27 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 34
and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features the features are as indicated above. 28 Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 35
for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that drives and is also available at: http://seatools.seagate.com. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports Manual, Rev. B 29 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 36
support/warranty_&_returns_assistance direct.seagate.com direct.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides self-service access to critical applications, personalized content and the tools that allow our partners to manage their Seagate - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 37
available. Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 38
32 Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 39
density 3, 5 ATA commands 21 ATA data-transfer modes supported 3 Australia/New Zealand Standard AS/NZ CISPR22 14 Australian compatibility 13 Conducted noise 8 Conducted RF immunity 12 Configuring the drive 16 connectors 17 CSA60950-1 13 current 3 cycles 13 Cylinders SATA Product Manual, Rev. B 33 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 40
temperature 10 Microcode 21 mounting 18 mounting screws 11 mounting the drive 16 34 N noise 8 nominal power 6 Nonoperating shock 11 Power consumption 7 power dissipation 7 power management 9 power on/off cycles 13 Power specifications 7 Power-management modes 9 Power-on to Ready 6 Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 41
Standby to ready 3 Start/stop times 6 Startup current 3 static-discharge 16 support services 30 Surge immunity 12 T technical support services 30 temperature 4, 6, 10 Temperature gradient 4, 10 timers 9 TPI 3 Track density write uncorrectable 22 Momentus Thin Series SATA Product Manual, Rev. B 35 - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 42
36 Momentus Thin Series SATA Product Manual, Rev. B - Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 43
- Seagate ST160LT007 | Momentus Thin SATA Product Manual - Page 44
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100586949, Rev. B, Printed in USA
Product Manual
Momentus
®
Thin Series SATA
100586949
Rev. B
March 2010
ST92503010AS
ST91603010AS