Home » Seagate Manuals » Hard Drives » Seagate ST33000651SS » Manual Viewer

Seagate ST33000651SS Constellation ES (.1) SATA Product Manual - Page 21

GB model current profile, Conducted noise, Note., Voltage tolerance

View all Seagate ST33000651SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

500GB model current profile Typical 500GB model 5V & 12V startup and operation current profiles 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 V line or an equivalent 15-ohm resistive load on the +5V line. • Using 12V power, the drive is expected to operate with a maximum of 120mV peak-to-peak square-wave injected noise at up to 10MHz. • Using 5V power, the drive is expected to operate with a maximum of 100mV peak-to-peak square-wave injected noise at up to 10MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.8.3 Voltage tolerance Voltage tolerance (including noise): 5V ± 5% 12V ±10% Constellation ES Serial ATA Product Manual, Rev. D 15

Section	Page
1.0 Introduction	9
1.1 About the Serial ATA interface	10
2.0 Drive specifications	11
2.1 Specification summary tables	11
2.2 Formatted capacity	13
2.2.1 LBA mode	13
2.3 Default logical geometry	13
2.4 Recording and interface technology	13
2.5 Physical characteristics	14
2.6 Seek time	14
2.7 Start/stop times	14
2.8 Power specifications	15
2.8.1 Power consumption	15
2.8.2 Conducted noise	21
2.8.3 Voltage tolerance	21
2.8.4 Power-management modes	22
2.9 Environmental limits	25
2.9.1 Temperature	25
2.9.2 Humidity	26
2.9.3 Altitude	26
2.9.4 Shock	26
2.9.5 Vibration	26
2.10 Acoustics	27
2.11 Test for Prominent Discrete Tones (PDTs)	28
2.12 Electromagnetic immunity	28
2.13 Reliability	29
2.13.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	29
2.14 Agency certification	29
2.14.1 Safety certification	29
2.14.2 Electromagnetic compatibility	29
2.14.3 FCC verification	30
2.15 Environmental protection	31
2.15.1 European Union Restriction of Hazardous Substances (RoHS) Directive	31
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive	31
2.16 Corrosive environment	31
2.17 Reference documents	32
2.18 Product warranty	32
3.0 Configuring and mounting the drive	33
3.1 Handling and static-discharge precautions	33
3.2 Configuring the drive	34
3.3 Serial ATA cables and connectors	34
3.4 Drive mounting	35
4.0 About FIPS	36
5.0 About self-encrypting drives	37
5.1 Data encryption	37
5.2 Controlled access	37
5.2.1 Admin SP	37
5.2.2 Locking SP	37
5.2.3 Default password	38
5.3 Random number generator (RNG)	38
5.4 Drive locking	38
5.5 Data bands	38
5.6 Cryptographic erase	38
5.7 Authenticated firmware download	38
5.8 Power requirements	39
5.9 Supported commands	39
5.10 RevertSP	39
5.11 ATA Security Erase Unit Command on SED SATA drives	39
5.12 Sanitize Device - CRYPTO SCRAMBLE EXT	39
6.0 Serial ATA (SATA) interface	40
6.1 Hot-Plug compatibility	40
6.2 Serial ATA device plug connector pin definitions	41
6.3 Supported ATA commands	42
6.3.1 Identify Device command	45
6.3.2 Set Features command	49
6.3.3 S.M.A.R.T. commands	50
Index	51
A	51
B	51
C	51
D	51
E	51
F	51
G	52
H	52
I	52
K	52
L	52
M	52
N	52
O	52
P	52
Q	52
R	52
S	53
T	53
U	54
V	54