Home » Seagate Manuals » Hard Drives » Seagate ST33000651SS » Manual Viewer

Seagate ST33000651SS Constellation ES (.1) SATA Product Manual - Page 40

Serial ATA SATA interface

View all Seagate ST33000651SS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

6.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0-4; multiword DMA modes 0-2, and Ultra DMA modes 0-6. For detailed information about the Serial ATA interface, refer to the "Serial ATA: High Speed Serialized AT Attachment" specification. 6.1 Hot-Plug compatibility Constellation ES Serial ATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA Revision 2.6 specification. This specification can be downloaded from www.serialata.org. Caution: The drive motor must come to a complete stop (Ready to spindle stop time indicated in Section 2.7) prior to changing the plane of operation. This time is required to insure data integrity. 34 Constellation ES Serial ATA Product Manual, Rev. D

Section	Page
1.0 Introduction	9
1.1 About the Serial ATA interface	10
2.0 Drive specifications	11
2.1 Specification summary tables	11
2.2 Formatted capacity	13
2.2.1 LBA mode	13
2.3 Default logical geometry	13
2.4 Recording and interface technology	13
2.5 Physical characteristics	14
2.6 Seek time	14
2.7 Start/stop times	14
2.8 Power specifications	15
2.8.1 Power consumption	15
2.8.2 Conducted noise	21
2.8.3 Voltage tolerance	21
2.8.4 Power-management modes	22
2.9 Environmental limits	25
2.9.1 Temperature	25
2.9.2 Humidity	26
2.9.3 Altitude	26
2.9.4 Shock	26
2.9.5 Vibration	26
2.10 Acoustics	27
2.11 Test for Prominent Discrete Tones (PDTs)	28
2.12 Electromagnetic immunity	28
2.13 Reliability	29
2.13.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	29
2.14 Agency certification	29
2.14.1 Safety certification	29
2.14.2 Electromagnetic compatibility	29
2.14.3 FCC verification	30
2.15 Environmental protection	31
2.15.1 European Union Restriction of Hazardous Substances (RoHS) Directive	31
2.15.2 China Restriction of Hazardous Substances (RoHS) Directive	31
2.16 Corrosive environment	31
2.17 Reference documents	32
2.18 Product warranty	32
3.0 Configuring and mounting the drive	33
3.1 Handling and static-discharge precautions	33
3.2 Configuring the drive	34
3.3 Serial ATA cables and connectors	34
3.4 Drive mounting	35
4.0 About FIPS	36
5.0 About self-encrypting drives	37
5.1 Data encryption	37
5.2 Controlled access	37
5.2.1 Admin SP	37
5.2.2 Locking SP	37
5.2.3 Default password	38
5.3 Random number generator (RNG)	38
5.4 Drive locking	38
5.5 Data bands	38
5.6 Cryptographic erase	38
5.7 Authenticated firmware download	38
5.8 Power requirements	39
5.9 Supported commands	39
5.10 RevertSP	39
5.11 ATA Security Erase Unit Command on SED SATA drives	39
5.12 Sanitize Device - CRYPTO SCRAMBLE EXT	39
6.0 Serial ATA (SATA) interface	40
6.1 Hot-Plug compatibility	40
6.2 Serial ATA device plug connector pin definitions	41
6.3 Supported ATA commands	42
6.3.1 Identify Device command	45
6.3.2 Set Features command	49
6.3.3 S.M.A.R.T. commands	50
Index	51
A	51
B	51
C	51
D	51
E	51
F	51
G	52
H	52
I	52
K	52
L	52
M	52
N	52
O	52
P	52
Q	52
R	52
S	53
T	53
U	54
V	54

Match case Limit results 1 per page

Constellation ES Serial ATA Product Manual, Rev. D

6.0

Serial ATA (SATA) interface

These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA

programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT

Attachment” specification.

6.1

Hot-Plug compatibility

Constellation ES Serial ATA drives incorporate connectors which enable you to hot plug these drives in accor-

dance with the Serial ATA Revision 2.6 specification. This specification can be downloaded from www.serial-

ata.org.

Caution:

The drive motor must come to a complete stop

(Ready to spindle stop time indicated in Section 2.7)

prior to changing the plane of operation. This time is required to insure data integrity.