Home » Seagate Manuals » Hard Drives » Seagate ST3300457FC » Manual Viewer

Seagate ST3300457FC Cheetah 15K.7 FC Product Manual - Page 48

FC-AL system errors

View all Seagate ST3300457FC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Table 5: Read and write retry count maximum recovery times [1] Read retry count Maximum recovery time per LBA (cumulative, msec) 0 51.87 1 59.85 2 203.49 3 231.42 4 295.26 5 327.18 6 359.10 7 446.88 8 538.65 9 570.57 10 598.50 11 (default) 1,534.97 [1] These values are subject to change. Write retry count 0 1 2 3 4 5 (default) Maximum recovery time per LBA (cumulative, msec) 23.94 35.91 39.9 51.87 79.8 107.73 Setting these retry counts to a value below the default setting could result in an increased unrecovered error rate which may exceed the value given in this product manual. A setting of zero (0) will result in the drive not performing error recovery. For example, suppose the Read/Write Recovery page has the RC bit set to 0, read retry count set to 4, and the recovery time limit field (Mode Sense page 01, bytes 10 and 11) set to FF FF hex (maximum). A four LBA Read command is allowed to take up to 253.11 msec recovery time for each of the four LBAs in the command. If the recovery time limit is set to 00 C8 hex (200 msec decimal) a four LBA read command is allowed to take up to 200 msec for all error recovery within that command. The use of the Recovery Time Limit field allows finer granularity on control of the time spent in error recovery. The recovery time limit only starts counting when the drive is executing error recovery and it restarts on each command. Therefore, each command's total recovery time is subject to the recovery time limit. Note: A recovery time limit of 0 will use the drive's default value of FF FF. Minimum recovery time limit is achieved by setting the Recovery Time Limit field to 00 01. 10.3 FC-AL system errors Information on the reporting of operational errors or faults across the interface is given in the Fibre Channel Interface Manual. The FCP Response returns information to the host about numerous kinds of errors or faults. The Receive Diagnostic Results reports the results of diagnostic operations performed by the drive. Status returned by the drive to the initiator is described in the Fibre Channel Interface Manual. Status reporting plays a role in systems error management and its use in that respect is described in sections where the various commands are discussed. 42 Cheetah 15K.7 FC Product Manual, Rev. C

Section	Page
1.0 Seagate Technology support services	7
2.0 Scope	8
3.0 Applicable standards and reference documentation	9
3.1 Standards	9
3.1.1 Electromagnetic compatibility	9
3.1.1.1 Electromagnetic susceptibility	9
3.1.2 Electromagnetic compliance	10
3.2 European Union Restriction of Hazardous Substances (RoHS)	10
3.3 Reference documents	11
4.0 General description	12
4.1 Standard features	13
4.2 Media description	14
4.3 Performance	14
4.4 Reliability	14
4.5 Formatted capacities	14
4.5.1 Programmable drive capacity	15
4.6 Factory-installed options	15
4.7 User-installed accessories	15
5.0 Performance characteristics	16
5.1 Internal drive characteristics	16
5.2 Seek performance characteristics	16
5.2.1 Access time	16
5.2.2 Format command execution time (minutes)	17
5.2.3 General performance characteristics	17
5.3 Start/stop time	17
5.4 Prefetch/multi-segmented cache control	18
5.5 Cache operation	18
5.5.1 Caching write data	19
5.5.2 Prefetch operation	19
6.0 Reliability specifications	20
6.1 Error rates	20
6.1.1 Recoverable Errors	20
6.1.2 Unrecoverable Errors	20
6.1.3 Seek errors	21
6.1.4 Interface errors	21
6.2 Reliability and service	21
6.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	21
6.2.2 Preventive maintenance	21
6.2.3 Hot plugging the drive	21
6.2.4 S.M.A.R.T.	22
6.2.5 Thermal monitor	23
6.2.6 Drive Self Test (DST)	24
6.2.6.1 DST failure definition	24
6.2.6.2 Implementation	24
6.2.7 Product warranty	26
7.0 Physical/electrical specifications	27
7.1 AC power requirements	27
7.2 DC power requirements	27
7.2.1 Conducted noise immunity	30
7.2.2 Power sequencing	30
7.2.3 Current profiles	30
7.3 Power dissipation	33
7.4 Environmental limits	35
7.4.1 Temperature	35
7.4.2 Relative humidity	36
7.4.3 Effective altitude (sea level)	36
7.4.4 Shock and vibration	37
7.4.4.1 Shock	37
7.4.4.2 Vibration	39
7.4.5 Acoustics	39
7.4.6 Air cleanliness	39
7.4.7 Corrosive environment	40
7.4.8 RoHS compliance statement	40
7.4.9 Electromagnetic susceptibility	40
7.5 Mechanical specifications	41
8.0 About FIPS	42
9.0 About self-encrypting drives	43
9.1 Data encryption	43
9.2 Controlled access	43
9.2.1 Admin SP	43
9.2.2 Locking SP	44
9.2.3 Default password	44
9.3 Random number generator (RNG)	44
9.4 Drive locking	44
9.5 Data bands	44
9.6 Cryptographic erase	45
9.7 Authenticated firmware download	45
9.8 Power requirements	45
9.9 Supported commands	45
10.0 Defect and error management	46
10.1 Drive internal defects/errors	46
10.2 Drive error recovery procedures	46
10.3 FC-AL system errors	48
10.4 Background Media Scan	49
10.5 Media Pre-Scan	49
10.6 Deferred Auto-Reallocation	49
10.7 Idle Read After Write	50
11.0 Installation	51
11.1 Drive ID/option selection	51
11.2 Drive orientation	51
11.3 Cooling	52
11.4 Drive mounting	53
11.5 Grounding	53
12.0 Interface requirements	54
12.1 FC-AL features	54
12.1.1 Fibre Channel link service frames	54
12.1.2 Fibre Channel task management functions	55
12.1.3 Fibre Channel task management responses	55
12.1.4 Fibre Channel port login	56
12.1.5 Fibre Channel port login accept	57
12.1.6 Fibre Channel Process Login	57
12.1.7 Fibre Channel Process Login Accept	58
12.1.8 Fibre Channel fabric login	58
12.1.9 Fibre Channel fabric accept login	59
12.1.10 Fibre Channel Arbitrated Loop options	60
12.2 Dual port support	60
12.3 SCSI commands supported	60
12.3.1 Inquiry data	65
12.3.2 Mode Sense data	65
12.4 Miscellaneous operating features and conditions	70
12.5 FC-AL physical interface	71
12.5.1 Physical characteristics	71
12.5.1.1 Physical description	71
12.5.2 Connector requirements	72
12.5.3 Electrical description	72
12.5.4 Pin descriptions	72
12.5.5 FC-AL transmitters and receivers	73
12.5.6 Power	74
12.5.7 Fault LED Out	74
12.5.8 Active LED Out	75
12.5.9 Enable port bypass signals	75
12.5.10 Motor start controls	75
12.5.11 SEL_6 through SEL_0 ID lines	76
12.5.11.1 Parallel Enclosure Services Interface (ESI)	76
12.5.12 Device control codes	78
12.6 Signal characteristics	78
12.6.1 TTL input characteristics	78
12.6.2 LED driver signals	79
12.6.3 FC Differential output	79

Match case Limit results 1 per page

Cheetah 15K.7 FC Product Manual, Rev. C

[1]

These values are subject to change.

Setting these retry counts to a value below the default setting could result in an increased unrecovered

error rate which may exceed the value given in this product manual. A setting of zero (0) will result in the

drive not performing error recovery.

For example, suppose the Read/Write Recovery page has the RC bit set to 0, read retry count set to 4,

and the recovery time limit field (Mode Sense page 01, bytes 10 and 11) set to FF FF hex (maximum). A

four LBA Read command is allowed to take up to 253.11

msec recovery time for each of the four LBAs in

the command. If the recovery time limit is set to 00 C8 hex (200 msec decimal) a four LBA read command

is allowed to take up to 200 msec for all error recovery within that command. The use of the Recovery

Time Limit field allows finer granularity on control of the time spent in error recovery. The recovery time

limit only starts counting when the drive is executing error recovery and it restarts on each command.

Therefore, each command’s total recovery time is subject to the recovery time limit. Note: A recovery time

limit of 0 will use the drive’s default value of FF FF. Minimum recovery time limit is achieved by setting the

Recovery Time Limit field to 00 01.

10.3

FC-AL system errors

Information on the reporting of operational errors or faults across the interface is given in the

Fibre Channel

Interface Manual

. The FCP Response returns information to the host about numerous kinds of errors or faults.

The Receive Diagnostic Results reports the results of diagnostic operations performed by the drive.

Status returned by the drive to the initiator is described in the

Fibre Channel Interface Manual.

Status reporting

plays a role in systems error management and its use in that respect is described in sections where the various

commands are discussed.

Table 5:

Read and write retry count maximum recovery times [1]

Read retry

count

Maximum recovery time per LBA

(cumulative, msec)

Write retry

count

Maximum recovery time per LBA

(cumulative, msec)

51.87

23.94

59.85

35.91

203.49

39.9

231.42

51.87

295.26

79.8

327.18

5 (default)

107.73

359.10

446.88

538.65

570.57

598.50

11 (default)

1,534.97