Seagate ST9900805SS Savvio 10K.4 FC Product Manual - Page 71

Signal characteristics

Get Seagate ST9900805SS PDF manuals and user guides View all Seagate ST9900805SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

9.5.12 Device control codes The drive inputs a Device Control Code on the DEV_CTRL_CODE lines at power up to determine the link rate on the Fibre Channel ports. Both ports run at the same rate. If the backpanel does not connect to these lines, the drive has 10K ohm pull up resistors that default the device control code to 7 (1.0625 GHz). Table lists the supported codes. Table 25: Device control code values 2 (pin 17) 0 0 0 0 1 1 1 1 1 (pin 18) 0 0 1 1 0 0 1 1 0 (pin 39) 0 1 0 1 0 1 0 1 Definition Reserved for power failure warning. Reserved for auto negotiation of link rate. Reserved. Reserved. Reserved. 4.250 GHz operation on both ports. 2.125 GHz operation on both ports. 1.0625 GHz operation on both ports. 9.6 Signal characteristics This section describes the electrical signal characteristics of the drive's input and output signals. See Table 21 on page 60 for signal type and signal name information. 9.6.1 TTL input characteristics Table 26 provides the TTL characteristics. Table 26: TTL characteristics State Input high Input low Output high (-EN Bypass A, B) Output low (-EN Bypass A, B) Output high (-Parallel ESI) Output low (-Parallel ESI) Output high (all other outputs) Output low (all other outputs) Voltage 1.9 < VIH < 5.5V -0.5V < VIL < 0.9V 2.4 < VOH < 5.25V VOL < 0.5V 2.4 < VOH < 0.9 VCC VOH > 0.9VCC 0 < VOL < .45V 2.4 < VOH < 0.9 VCC VOH > 0.9VCC 0 < VOL < .45V Current IIH = ±500nA max. IOL = ±500nA max. IOH < -3mA IOL < 3mA IOH < -2.4mA IOH < -500µA IOL < 2.4mA IOH < -1.6mA IOH < -500µA IOL < 1.6mA Savvio 10K.4 FC Product Manual, Rev. A 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Savvio 10K.4 FC Product Manual, Rev. A
65
9.5.12
Device control codes
The drive inputs a Device Control Code on the DEV_CTRL_CODE lines at power up to determine the link rate
on the Fibre Channel ports. Both ports run at the same rate. If the backpanel does not connect to these lines,
the drive has 10K ohm pull up resistors that default the device control code to 7 (1.0625 GHz). Table lists the
supported codes.
9.6
Signal characteristics
This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 21
on page 60 for signal type and signal name information.
9.6.1
TTL input characteristics
Table 26 provides the TTL characteristics.
Table 25:
Device control code values
2
(pin 17)
1
(pin 18)
0
(pin 39)
Definition
0
0
0
Reserved for power failure warning.
0
0
1
Reserved for auto negotiation of link rate.
0
1
0
Reserved.
0
1
1
Reserved.
1
0
0
Reserved.
1
0
1
4.250 GHz operation on both ports.
1
1
0
2.125 GHz operation on both ports.
1
1
1
1.0625 GHz operation on both ports.
Table 26:
TTL characteristics
State
Voltage
Current
Input high
1.9 < V
IH
< 5.5V
I
IH
= ±500nA max.
Input low
-0.5V < V
IL
< 0.9V
I
OL
= ±500nA max.
Output high (-EN Bypass A, B)
2.4 < V
OH
< 5.25V
I
OH
< -3mA
Output low (-EN Bypass A, B)
V
OL
< 0.5V
I
OL
< 3mA
Output high (-Parallel ESI)
2.4 < V
OH
< 0.9 V
CC
V
OH
> 0.9V
CC
I
OH
< -2.4mA
I
OH
< -500μA
Output low (-Parallel ESI)
0 < V
OL
< .45V
I
OL
< 2.4mA
Output high (all other outputs)
2.4 < V
OH
< 0.9 V
CC
V
OH
> 0.9V
CC
I
OH
< -1.6mA
I
OH
< -500μA
Output low (all other outputs)
0 < V
OL
< .45V
I
OL
< 1.6mA